Forum Post: RE: About setup time of High-speed mode
Hi Okamoto san,Have you tried with 51K ohm pull up resistor which has used in the EVM circuits?Regards,Hyun
View ArticleForum Post: RE: Query regarding External pull up and pull down needed with...
Maheen,Please refer the Terminal function in the datasheet for the external Pull Up and Pull down requirements.http://www.ti.com/lit/ds/symlink/tms320c6713b.pdfSometimes we required external pull...
View ArticleForum Post: RE: C6654 DDR3 initialization problem
Mark,This forum post is for C6654. We have recently found that the C665x GEL does not provide all of the registers needed to properly enable Partial Automatic Leveling. The GEL provided successfully...
View ArticleForum Post: RE: Multicore handling DDR3 data parallelly result in conflict !
Wei,A couple of questions here:[quote user="wei he1"]As we known, the size of DDR3's bank is 16MB[/quote]Can you share the formula you used to come to 16MB?[quote user="wei he1"]8 core can read/write...
View ArticleForum Post: unable to receive data to ttyS1 on XTCIEVMK2X board
Hi,I am using XTCIEVMK2X board. The SOC on the board has two UARTs. UART0 is exposed as SOC Linux console and UART1 is going to Expansion Connector A. The dmesg of Linux shows these two UARTS as...
View ArticleForum Post: RE: Interrupt service routine entry address（ dissembly code:...
Summer,To help us understand your problem better, can you provide more details on what you are doing? If it is possible, attach the piece of the code you are working on (including where you are...
View ArticleForum Post: RE: Triggering Shared Peripheral Interrupts of ARM Corepac from...
Thanks a lot for your feedback and example code for this issue.May I ask which BIOS and XDC version you are using please?I am working with our BIOS team to confirm if K2H A15 interrupt is only...
View ArticleForum Post: RE: Feasible or not? Video Capture through VPORT(VIP), DM8168
Hi Badri, Thank you for your reply! I find them very helpful. I'd like to check out the driver and HD usecases which you indicated.NaroahJan/08/2014
View ArticleForum Post: RE: About C6670 PCIe Device ID
Hi Eric,Thank you for the reply.Actually this question was from our customer.Their system boot from SPI NOR Flash and they aren't using IBL.So, user can customize their own PCIe Device ID and it could...
View ArticleClik here to view.
Forum Post: RE: SRIO doorbell interrupt cannot be trigger
[quote user="steve zhang"]1.Can consumer receive doorbell from producer?I do two tests one by one.First I map Doorbell reg0 and bit0 to INTDST0,Second I map doorbell reg0 and bit0 to INTDST16.When...
View ArticleForum Post: RE: TMS320C6678 Reference Clocks
Tom S,There is no downside to your system design. 100MHz is equally valid for the DDR reference clock. The internal PLL can generate the optimum DDR3 frequencies from both.Use of the internal mux for...
View ArticleForum Post: RE: Power Consumption of 66AK2H06
Hi AlexanderThe power estimation model creation is still work in progress. We will have an alpha release available internally by end of the month, which will be available/enable field teams to support...
View ArticleForum Post: RE: unable to receive data to ttyS1 on XTCIEVMK2X board
Hi,Please reply to the above post.Thankskg
View ArticleForum Post: RE: K2H12 Keystone II TSREFCLK SyncE clock
Sachin,I see you found an inconsistency in our recommendations. Going forward, we intend to keep the single resistor solution for the LJCB and the dual resistor solution for the LVDS inputs due to the...
View ArticleClik here to view.
Forum Post: Understanding Timing Diagram of VPIF
Hi, I wanted to understand certain terminologies used in Raw Capture Progressive Mode:a. Vertical Blanking , min = 3lines ---------- Is it same as telling it needs a minimum of 3...
View ArticleForum Post: K2H Starterware equivalent
I'm attempting to run a benchmark of the ARM Cortex-A15 core on the C66AK2H12 in comparison with the OMAPL138 Cortex-A9 core, both on bare metal. The L138 was easy enough after downloading the...
View ArticleForum Post: RE: C6654 DDR3 initialization problem
Tom,Thanks for the continued assistance but I think we are not on the same wavelength anymore. I already have a repeatable DDR3 configuration for these boards, and have been using it for at least 6...
View ArticleForum Post: RE: Where is Technical Reference Manual Available for OMAP-L1x,...
Thank-you HRThank-you PubeshThank-you ShankariBest,Robert
View ArticleForum Post: RE: 24bit / 192khz PCM/BWF professional audio recorder
What media are you recording to?Do you need a display?Power requirements?
View Article