Forum Post: RE: New to DSP
Hi Gregory,The C5000 Teaching ROM comes to mind - http://e2e.ti.com/group/universityprogram/educators/w/wiki/2040.c5000-teaching-rom.aspxIt includes several labs and slides for audio processing like...
View ArticleForum Post: TMDXEVM8148 - dm814x am387x EVM -- Help Needed
I am new to ARM development but have extensive experience in embedded real-time dvelopment. I have just received the EVM and was following the setup instructions from the EZ software development...
View ArticleForum Post: Cannot open the image processing input page on browser for...
Hi all,I'm using DSPC-8681E (which integrates four TMS320C6678 multi-core DSPs:DSP0~3) and I'm trying to run the image processing example provided in the driver package.I'm able to follow the steps...
View ArticleForum Post: BTSEL Clarification
I have a DM368 based design that normally boots from NAND but can also boot from an SD card if the user presses a particular switch while turning on power (pressing the switch effectively pulls up...
View ArticleForum Post: Boot logo on additional video out modes
The current sdk supports boot logo (via uboot) on HDMI, what would be the process to enable that for other video modes (DVO/NTSC/PAL etc) ?The forums have a number of suggestions but has anyone had...
View ArticleForum Post: RE: C6748 SERIAL BOOT BINARY QUESTION
Hi Shankari,Customer has one more question.They 6748 they are using is permanently attached to the embedded linux machine and they had planned on using the serial port to transfer the image to the 6748...
View ArticleForum Post: RE: [DM814x] VSS_* pins internal connection
Thanks Steve,There was slight noise issue at the video output of VDAC, so wanted to check about VSS and VSSA grounds.Best regards,Hayden
View ArticleForum Post: RE: GPMC access?
Dear Pavel-san,Thank you for your quick reply.We tested to reset M3 by using DUCATI_M3_RST1/2 bit of RM_DEFAULT_RSTCTRL register. Please see the below.bit3:...
View ArticleForum Post: RE: Why are C6670 DDR3 address pins A15/14/13 connected to...
Hi Tom,I’m so sorry for not repling sooner.Thanks for your information.Best regards,j-breeze
View ArticleForum Post: RE: Could c6678 generate SRIO Tx completion interrupter?
Hi atower,Have you taken a look at the SRIO_LoopbackDioIsrexampleproject included in the MCSDK? It can be found in the following location after you install the MCSDK (below path is for MCSDK version...
View ArticleForum Post: RE: dMAX service McASP event in spru795d
Thank you Sivaraj!I am writing a program for a long time and like to understand how hardware works. It helps make programs more quality. At least it helped earlier when I write programs for AVR, ARM,...
View ArticleForum Post: RE: sampling frequency
I am using normal PC Microphone. Yes, I connected speakers to J4. Also, I am putting a break point in my program and looking at the magnitude of the samples coming into the DSP loop. I am using...
View ArticleForum Post: RE: TI eStore no longer has EVMK2H?
Hi JohnYou should be able to order the EVM from the estore now. You might see an "out of stock" message, but you can ignore the message, it is being spit out because of some logistic issue, which will...
View ArticleForum Post: RE: communication between PC and DSP (DSPC-8681E)
Hi Thanks for the reply. I did run core 0 first and then run core 1-3. However it turned out that only core 0 works...
View ArticleForum Post: RE: New to DSP
Thanks for the quick answers. I'll try out that tutorial once I have the DSP unit again.Also, thanks for the heads-up, Bill. I'll keep that in mind.The goal is to filter audio and send a control signal...
View ArticleForum Post: RE: K2H Starterware equivalent
Hello,We don't have anything like that officially available yet in our MCSDK. So far you need to run Linux on ARM A15. The release is available...
View ArticleForum Post: RE: SRIO doorbell interrupt cannot be trigger
It is not clear to me how you are manually triggering the Event 112. Here is what I'd suggest use the INTDST 16 and use the primary interrupt (Event 20) to the core instead of the CIC event (Event...
View ArticleForum Post: RE: "Working on IMGLIB for OMAPL138 development kit"
Yes C64x+ will work fine for C674x.Regards,Travis
View ArticleForum Post: OpenMax Test Bench - What is it for?
What is the purpose of the OpenMax Test Bench? Can I use it to test the H.264 encoder?I need to do multiple encodings of yuv source file, change the encoder parameters for each test and save the...
View ArticleForum Post: RE: How to use libflame in 6678
Hi,The official LibFlame release from TI will be through MCSDK-HPC. So please wait for the TI MCSDK-HPC release. Also the initial target platform for MCSDK-HPC is for K2H devices.Xiaohui
View Article
