Forum Post: bigger (=readable) diagram on multicore SDK building blocks
on this pagehttp://www.ti.com/tool/bioslinuxmcsdk#0there is a red colored thumb nail image. when clicking on it the image still has the very same size and thus the click provides no advantage in...
View ArticleForum Post: RE: question about intraFrameInterval value
Hi Badri,I am sorry that I make a mistake. It works well and thanks.
View ArticleForum Post: RE: C6655 compatible NAND devices for boot
All ONFI compatible NAND devices are supported by the RBL. For non-ONFI NANDs, the RBL can boot only from devices whose NAND geometry can be determined either from matching manufacturer/device ID with...
View ArticleForum Post: RE: DVRRDK screen shot capture available for DM814x?
Yes capture of HDMI screen output is supported on 814x as well. There is no usecase on 814x that demonstrates this but you can...
View ArticleForum Post: RE: c6678 NDK client demo:TCP: Retransmit Timeout
From Wireshark capture, it looks like DSP sent the echo packets back but didn't get the response from PC within time, so the packets re-transmitted via TCP, the PC received duplicates. The echoc.exe is...
View ArticleClik here to view.
Forum Post: RE: C6657 SPI boot problem
I do have -e _c_int00 in my rmd file. I change spiboot.cmd file to allocation all into MCSC. Please see attached map and rmd files.After the boot, I stop the processor and file PC is in a loop. see...
View ArticleForum Post: RE: Computing real number FFT
Mark,thanks for replying.So if Ichange the typeofvector forLDATA, which usesthe formatQ.31willwork? Or there isnothow to calculate theFFTofa vector ofreal numbers?There is function RFFT32 in the DSPLIB...
View ArticleForum Post: RE: What kind of USB DMA protocol should I use with Isochronous...
J-breezeTransparent mode is used.ThanksDavid
View ArticleForum Post: RE: EVM6657 PCIe enumeration failure
While I wait for the actual FPGA file (if you have it, please post it here!), could you explain a bit more about the actual issue? I found a thread with your posts which describe the following...
View ArticleForum Post: Simulation Problem with C5416 when simulating on C55xx Rev 3.0...
Hello, After making some research, I learnt that i can run C54x code on C55xx simulator. Simply, I would like to run FIR filter code on C5416 device. According to instruction that i got, I first tried...
View ArticleForum Post: RE: simultaneous SRTP and IPSec using Keystone security accelerators
Hi Jeff,Can the security accelerators on the 66AK2H06 perform SRTP and IPSec at the same time?Though I am not a Keystone Architecture expert,I am pretty sure IPSec and SRTP share the encryption and...
View ArticleForum Post: RE: Query regarding syslink and HDVICP usage on QNX
QNX supports the HD-VICP themselves. They have mulitple customers using it. Customer needs to enter into a services engagement to get the software and support.
View ArticleForum Post: RE: how to replace memcpy with neon based on memcpy?
Hi,YoungWhen I install NVRSOURCE_04.00.00.03.tar.lzma package ，it says the data of package is broken，can you give a copy of NVRSOURCE_04.00.00.03.tar.lzma package my email : xiaodeo@126.comthank a...
View ArticleForum Post: RE: How to test the rate for PCIE between C6678
Hi Eric Thank you for your answer,I have understanded what you said. So if we want to test the average rate of large size transfer(so we can ignore the latency from data going out of Tx to...
View ArticleClik here to view.
Forum Post: sfh_OMAP-L138.exe stop at: Flashing application u-boot-ais.bin...
I cann't write u-boot-ais.bin to my board. The step is:1 build u-boot2 using AISgen_d800k008.exe and u-boot file to gernate BIN file:u-boot-ais.bin3 flash to board, the command line is:...
View ArticleForum Post: RE: "No ETH PHY detected" error in Leopard DM368
Dear TitusThanks for your comment. I replaced your file with former file that you sent me and then I built the new image file. After flashing the image file into the SD Card and booting the board,...
View ArticleForum Post: RE: OMAP-L138 ESD compatibility IEC 61000-4-2
hi Mukul :I have the same problem, and somebody encounter the same problem also.http://e2e.ti.com/support/dsp/omap_applications_processors/f/42/t/99038.aspxI have used a External 3.3V Clock Source,and...
View ArticleForum Post: RE: Can GV7601's YUV 10bit Output be connected to DM8168 8Bit...
Hi,What about the output?Can the davinci video output be connected to a chip that accept 8 bits YCbCr 4:2:2 format at 1080p 30fps?Thanks in advanceAlberto
View ArticleClik here to view.
Forum Post: RE: question about the resolution tiler supported
Hi, BadriNow, I have realized the image rotation(image resolution1080P or more than 1080P), however there is a flaw on the image left.My link as follow:capture --> dup(output:4) --> merge(in:4)...
View Article