Forum Post: how to pack rsz output of raw into 12bit?
I need to get isp processed RAW 12 bit data out of ipipe (case 2).Therefore, I let data from ipipe go into rsz with the pass-through mode.I got 16 bit RAW from rsz.How can I get 16->12bit pack...
View ArticleForum Post: RE: TMDSEVML138 uboot audio expansion
I am using the logicPD board and the codec is set to master mode and has its own oscillator which is also connected to AHCLKX. Ive been observing chip select for the spi flash boot rom and when...
View ArticleForum Post: RE: SPI and USB conflict on LCDK
Hi Alex,Could you please attach your board file which has both the USB and SPI init ?
View ArticleForum Post: shmIpcBenchmark project
in the project：C:\ti\pdk_C6678_1_1_2_6\packages\ti\transport\ipc\examples\shmIpcBenchmarkit include many libs in the cmd generated after build the project. but i do not know how these libs included in...
View ArticleForum Post: RE: SPI TXINTFLG set as soon as ENABLE is set
I should have given a little more information about my application.I am using the EDMA to respond to the TXINTFLG conditions, generally speaking. I am not making use of the SPI TX Interrupt as such, so...
View ArticleClik here to view.
Forum Post: DM36x composite analog output problem
We use 320x240 and 640x480 YUV sensors for connecting DM36x chip based on Appro reference design (the 320x240 is resized to 640x480 before sending to display process). The analog TV output works but we...
View ArticleForum Post: dm8168 chip temperature
Hi,we use DM8168, and we wonder if there is a sort of undocumented feature like temperature sensor integrated in the chip.Otherwisewhat is themost reliable way toknowthetemperatureof the chip? best...
View ArticleForum Post: RE: DDR3 Inizialization failure in C6678
Hi Henry,It's not clear from you post the method that you are using to configure the memory. Are you using a GEL? I would recommend that you start with the GEL file delivered with MCSDK, modify it with...
View ArticleForum Post: RE: Multicore DSP evaluation board
Hi Danillo,HDMI is not supported by the multi-core KeyStone I and II families. You would have to pair the KeyStone device with a separate components that can handle the video. KeyStone devices do...
View ArticleForum Post: RE: CS2 for C6746
Hello Titus,Thanks for the quick response. Yes, I have a NOR flash that uses chip select two. I ported existing program for NOR flash with read/write/boot function that worked with the C6712. When the...
View ArticleForum Post: RE: Srio utility of local device IDs
Hi Ganapathi , Thank you very much for your reply, I succeed to use the BRR routine registers and I configured with different IDs for each port but my question is : what is the purpose of using...
View ArticleForum Post: RE: Hyperlink Station Management Capabilities/Status Message
That is correct.Regards, Eric
View ArticleForum Post: RE: SPI Clock and Data lines routing / distribution to multiple...
Antony,As far as the chip select to all 50 devices you are right there is a limitation on the available GPIO, especially in my particular system so in this case I will most likely use the appropriate...
View ArticleForum Post: RE: GPIO sampling rate on C6670
Hi Hardik,The GPIO module is considered a low speed module and was never intended for data sampling. You have made a couple of bad assumptions in you analysis.First, the 12C input timing requirement...
View ArticleForum Post: RE: McBSP example in C6657
Steve,Sorry that I could not get back to you sooner. It might be better to start a new thread for different issue next time, that all the other community members could be notified and try to help as...
View ArticleForum Post: RE: "PORT_OK" bit in the SRIO register SP_ERR_STAT
Hi Xining,Control symbols are physical layer message elements used to manage link maintenance, packetdelimiting, packet acknowledgment, error reporting, and error recovery. They are protected by their...
View ArticleForum Post: RE: 1080i60 display issue
Hi Csaba, Yes, your understanding is correct, , we patched the HDVPSS that comes in the Overlay, i.e, hdvpss_01_00_01_44. At this point I haven't seen any difference or problems using the...
View ArticleForum Post: RE: TMS320C6678 to configure the SPI port of the TI lmk04828...
Hi Viktorija,If you are only using the bus to configure the LMK04828, I suggest you use three GPIO pins an bit-bang the interface. This would allow you to reconfigure the data bit from output to input...
View ArticleForum Post: RE: EDMA Slow Transfer speed
Sam,Is it correct that the ISR reads only 1 byte from the UART's receive FIFO and then returns from the ISR? And the DMA is not enabled in this case, right?The fact that the ISR waits 200-300 us...
View ArticleForum Post: RE: C6657 DDR3 DQ vs DQS timing
Jim,I want to let you know that we have not forgotten about this issue. We have busy with other activities. We are coordinating the right resources to address this in the coming weeks.Tom
View Article