Forum Post: RE: 66AK2H6 EVM, performance and change from Keystone 1 to...
Hello Chad,thanks for your fast reply. I have been out of office the last two days. Glad to hear that the platform change should be not a huge problem. I am looking forward to the responses of your...
View ArticleForum Post: RE: C6670 to DDR3 Interface (Is the C6670 truly JEDEC Compliant?)
Hi Dan,I would like to understand your question better. Could you tell me which JEDEC spec has the skew guidelines in your example?Regards, Bill
View ArticleForum Post: The capabilities of DM8148
Is DM8148 able to encode and decode 1080p30 simultaneously?(1080p30 enc + 1080p30 dec)
View ArticleForum Post: What the difference between ARM and DSP core when accessing FPGA...
Hello everyone, I want to use EMIFA to access a dual port RAM in FPGA, which is designed to be 16-bit in width and 256-byte in depth. I have configured the EMIFA to be 16-bit data width, and used...
View ArticleForum Post: RE: McASP/EDMA3 issue
As suggested, I enabled clock check, and made sure, I do not start the DMA, and the McASP frame sync generation, before enough time has elapsed to permanently clear the clock check error bit in the...
View ArticleForum Post: RE: SM28VLT32-HT SPI flash on OMAP-l137
Hi Claus,Could you please share the PSP version that you are working?We will get back to you shortly with the required information.I hope you will find many good answers here and in the TI.com...
View ArticleForum Post: RE: Boot Splash Screen on the DM814X
Hi Stephen,Thank you for the response. There was a E2E forum titled "uboot splash screen for DM816X for SD/Dvo2" and I think we can switch to discuss this issue on that Forum. The title is realted to...
View ArticleForum Post: RE: c6654 set up an interrupt on a GPIO through CIC0
Emmanuel,Please note several things In order to use GPIO[31-16] in C6654/5/7 devices. 1. GPIO[31-16] are pin muxed with other peripherals. You need to program PIN_CONTROL_0 register to enable GPIO...
View ArticleClik here to view.
Forum Post: 816X/389X EVM, Sandisk SATA 3 X110 SSD communication not working
Hello,I have an 816X/389X EVM and am testing the SATA interface with various SSDs. Of the ones I've tested (Intel, Kingston, Crucial SATA 3s, Apacer, WD, Greenliant) the drives are detected and work...
View ArticleForum Post: RE: Fail to Receive ARP Request on PA_emacExample (C6670)
Aditya,In no loopback mode, first check if the switch of 6678 EVM can receive packets, you can look at the memory 0x2090b00 and 0x2090c00 range, those registers are explained in table 3-2 of...
View ArticleForum Post: Can the DM816x capture image size 3320 x 2496 ?
Hi, We want to use DM816x to capture CCD sensor data, the image size is 3320 x 2496, can the VIP0 and VIP1 capture this size?Thanks!John
View ArticleForum Post: Keystone II NAND EMIF Boot
Greetings,I have a K2EVM and I'm using u-boot as a bootloader to get SPI NOR and NAND EMIF booting to work. I've gotten NOR booting to work very easily by building the...
View ArticleForum Post: RE: C5535 emulator USB Driver
Hi Andrew,It sounds like the FTDI EEPROM (U2) was not programmed correctly. FTDI provides a tool to program that EEROM.Try flashing the FTDI EEPROM with FTDI FT_PROG tool and the template file from...
View ArticleForum Post: DM365 Crash (SW lock-up)
We are struggling with a DM365 design. During first prototype run, things looked good and we're able to run Linux and run many tests. Only very minor changes were made to the PCB and on the current...
View ArticleForum Post: RE: spO2 desktop application (C5515 EVM MDK Pulse Ox Application)
Hi May,Are you trying to record/ save the files from the PC Application? I've never tried to do this before.We have uploaded the pulse ox PC application source to the forum - maybe it will help...
View ArticleForum Post: RE: PCIe Controller Failure
Hi Pavel,Thanks for the info.Disabling ASPM is an acceptable solution for our application.Michael
View ArticleForum Post: RE: Does C6748 = OMAP-L138 at the silicon level
Hi Dean,C6748 is a DSP boot device(on reset the DSP comes up first) while OMAPL138 is an ARM boot device (on reset the ARM comes up first so to run DSP code the ARM needs to bring DSP out of reset and...
View ArticleForum Post: RE: FileRd- Dec- FileWr
The output of decoder is in NV12 format. ie. YUV420SP . Y will be in a separate buffer and UV will be in a separate buffer. You can google for details on the format but the issue you should not copy...
View ArticleForum Post: RE: Connect Leopardboard DM365 to an LCD panel
Include additional LED driver will ease your life. Take a look at TI's TPS61042 for example. The CTRL pin is combined enable and PWM control pin. The signal can be connected to DM365's PWM output,...
View ArticleForum Post: Error in code generation from simulink to C6747
Hi all, I am trying to generate C code from a Matlab(2013a)-Simulink simple model (ADC in to DAC out). The model is based on C6747 EVM and the version of Code Composer Studio is V5.3. An error as...
View Article