Forum Post: RE: [OMAPL138] Problems with loading the SPI writer file on ARM core
Hi Shankari,I use ZOOM OMAP-L138 EVM from Logic PD.I've tried both, but it didn't work.I am slightly confused, because I can't even load the SPI writer into the ROM memory. Can the CCS generate such...
View ArticleForum Post: RE: DM365IPNC-MT9M034 Ip-cam is not working
Could be because all ip's are assigned already to some other devices? Confirm on that.Worst, case, give try with SD card, till the time you could resolve the network issue.
View ArticleForum Post: RE: Linux OMAP L138
Hi Alexey,If your operating system is Linux and if you use gdb as debugger, you can do a core dump by following the TI WIKI...
View ArticleForum Post: DSP's high load affected M3 codec's h.264 bit generate.Why?
Hell,TI sir.in our board,we use DSP to perform audio echo cancel.However,for a mass data progressing,DSP's load is high.And If we enable the aec with DSP,the M3 codec will not generate h.264 stream.We...
View ArticleForum Post: RE: DM8168 Decoding External Display
Thanks for your timely help. With you help, I have modified the load address and entry point of Linux to 0xD0008000, and then ./run_make.sh ti816x-etv sys_all. There is some errors in the running...
View ArticleClik here to view.
Forum Post: RE: How to Use 6678 eth0 and eth1 with different MAC simultaneously
Hi John,as I was skipping through your code i've met with unknown identifiers PLATFORM_AMC_INTERRUPT and PLATFORM_AMC_EVENTID. Would you give me a hint what should it be ?Thanks,BS.
View ArticleForum Post: RE: DM8168 PCIe EP mode
can you give me your qq number or mail address?i want to ask for your some help .thanks very much.
View ArticleForum Post: RE: how to set the hw breakpoints/watchpoints by sw without using...
Hi Galip,Typically we think of breakpoints as IDE-only i.e. we manually have to set BPs at certain locations. However it would be neat to programmatically trigger a breakpoint. Naturally we can do this...
View ArticleForum Post: RE: Run opencv application on DM814X
[quote user="qijie"]2). If it is need set DISPLAY environment variable ? if Yes , what is the value ?[/quote]Can you try with export DISPLAY=0:0Refer to the below e2e thread for more...
View ArticleClik here to view.
Forum Post: XTCIEVMK2X Rev1.0: ARM view and DSP view of DDR3A and DDR3B
This is regarding the ARM view and DSP view of DDR3A and DDR3B. It is still not clear after going through the below post on DDR3A and DDR3B mapping and ARM and DSP...
View ArticleForum Post: RE: How can I improve the frame rate in video processing?
Shengzhe,Are you working with EZSDK 5.05.00.02?Are you using DM814x EVM or DM814x based custom board?Regards,Pavel
View ArticleForum Post: RE: USB Webcam with OMAP-L138 LCDK
Hi,I would like to use my USB webcam(logiteck) interface to OMAPL138 platform, it recognized the driver and how the image need to bring in to the LCD and how the way to take the snapshots to read the...
View ArticleForum Post: a question about processing time calculation for TMS320DM6437...
Hello I have a question about processing time calculation for TMS320DM6437 resizer. In datasheet spru977d.pdf (Video Processing Front End, User's Guide, section 5.6.5.2)we can find the following...
View ArticleForum Post: How to load .out file without flashing in Linux
I compiled my application using gcc. I want to load it without flashing just like loading an application in CCS. How can I do it?The below link explains how to load by...
View ArticleForum Post: RE: How to modifile the video data before HDMI(60fps) transmit...
You could modify the example DSP audio codec that is written in OpenMAX. It's somewhere in the EZSDK. Then, you can insert this codec into your chain.
View ArticleForum Post: RE: [C6748] query about DVDD18 pull up to 2.7V
Daisuke,Apologies for the delay in response, I have already forward your request to internal colleague and there is a delay in response due to thanks giving vacation will get back to you...
View ArticleForum Post: RE: 10 MBps / Full duplex packet loss on 3PSW configured as switch
Dear Pavel,is there any update regarding this issue? As a workaround, I've patched the cpsw driver disabling the 10/FULL configuration, but certainly this is not the proper solution.Have you any...
View ArticleForum Post: C6678 PCIESS link training fail issue
Hello people.I have an issue about PCIe communication between a C6678 EVM and Xilinx Spartan 6 EVM. I'm connecting a TMDXEVM6678L EVM to Xilinx SP605 EVM on PCIe port. In this set, DSP is RC and FPGA...
View ArticleForum Post: interfacing in matlab and submission of report
sir,our mentor prof. Ashutosh kar is out of station for some emergency purpose . so can we submit the report without his signature? but we trying our best get that.i am also facing problems in target...
View ArticleForum Post: Connect PIR sensor analog output to DSP
Hi,I am thinking of doing a project that involves connecting a PIR sensor to a high performance DSP such as the TI C6713. I would like to take the analog output of the PIR and send it to the DSP for...
View Article