Forum Post: RE: Slow rising rate when switching PINMUX8 EMA_D[15] and GP3[7]
Hi Weili,Have you resolved this issue?please help me to close this discussion if you resolved this...
View ArticleForum Post: RE: L138 Power off Problem
Hi Dinu,Thanks for the Update good that have resolved this issue.please help me close this discussion if you resolved this...
View ArticleForum Post: RE: musb and multiple devices
I need some help here, but I'm getting no response. Is someone even looking at this issue?Further investigation seems to indicate that the musb host controller can only handle 16 devices at a time....
View ArticleForum Post: RE: OMAPL137 - 456MHz - how to set PLL setting for 456HMz version ?
Hi Grzegorz ,Have you checked with the new settings for 456Mhz system Clock ?Please help me to close this discussion if you're done with the new...
View ArticleForum Post: RE: DM36x Image Encoder Hang
If your issue is resolved, you can try below suggestions.http://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/100/p/287040/1001517.aspx
View ArticleForum Post: RE: build CSL2_DAT_DEMO in edma3_lld_02_11_06_01
Krishna,I am not sure what your current status of building CSL2_DAT_DEMO. I have been struggling in it for quite a long period until now. I made it port the demo code from evmDA830 to evmTI816x. I had...
View ArticleForum Post: How to increase DM8148 1080P60 capture gstreamer pipeline frame...
Hello,We are working on DM8148 custom board and EZSDK 05 05 02 00. The custom board is similar to TI EVM board.We use an external HDMI decoder to connect DM8148. Our aim is to capture the video,encode...
View ArticleForum Post: RE: Troubleshooting C6670EVM PCIe boot with multiple cores
I finally got all cores booting. I initially had all of shared L2 SRAM allocated for data arrays. That is why I moved SharedRegion 0 to DDR3. However, when I freed up some of shared L2 SRAM...
View ArticleForum Post: RE: C667x sRIO BER testing with the embedded test patterns...
Hi Daisuke,Please see Advisory 17 - Corruption of Control Characters in SRIO Line Loopback Mode Issue in the errata document for C6678 (http://www.ti.com/lit/pdf/sprz334). Given the content of this...
View ArticleClik here to view.
Forum Post: RE: TMDXEVM6670LE Configuring Debugger Issue
Here's what I have for a driver on a Windows 7 PC. However, I don't recall where I got the driver.Kevin
View ArticleForum Post: RE: EDMA3 - EMIFA used by DSP when Linux is running on ARM
My project was quite a long time ago. I was using 2.6.32 from one of TI PSP packages. I was using EDMA on a SPI port on the DSP. I was getiing weird panics in conflict with EDMA on UART on the ARM. I...
View ArticleForum Post: RE: 5505 USB Bootstrap Fails Enumeration on USB3.0 port
Gary,C5505 has only been verfieid with USB2.0. We currently do not have any data on USB 3.0 verification.Regards.
View ArticleForum Post: RE: XDS Jtag interface to C5535
In C5515 data manual, it refers to XDS560 Emulator TRM, SPRU589. There is Table 3-4 on p23 recommended 14-pin header parts. Also discussed are resistor values.Hope this help.
View ArticleForum Post: RE: C674X Mathlib error #821: badly formed pragma
Thanks George.For forum records: I replied to this post to state that I find this information very important but very difficult to find. (And to point out the MATHLIB Wiki FAQ is empty).I created a...
View ArticleForum Post: RE: C6678 HyperLink Debugging
I had test between two 6678 EVMs connected via Hyperlink cable. The registers you dumped seems right (only serdes_ctrl_sts1 differs because I used async clock). Can you try re-configure Control...
View ArticleForum Post: Reserve DMA channels for DSP in Linux Kernel
Hi,I'm using the CriticalLink L138 board with the OMAPL138 processor on it. At the moment I have major problem to get the EDMA transfers on the DSP Running while Linux is running on the ARM core.I got...
View ArticleForum Post: DM368 Power Estimation spreadsheet
I found the DM368 Power Estimation spreadsheet and I’m trying to adjust setting. There are some fields that are password protected and it seems as though nobody has the password. I looked on the TI E2E...
View ArticleForum Post: hwo to set gpio4 as INT4 interrupt on 6455
helo ,my dsp is 6455. i f i wan to set gpio4 as int4 interrupt , is there interrupt select register to use ?? hwo to finish it ?thanks
View ArticleForum Post: RE: Capture UXGA resolution
Hi Steven, From the captuer port point of view, it can be supported, there might be minor changes required in the capture link to support this resolution. Regards,Brijesh
View Article