Forum Post: RE: DM8107 59.94 1080i/720p display
I have come across a semi-solution. If I do DVO2 output only everything seems to work. My testing up to this point I have had HDMI and DVO2 tied. So it appears there is some instability at 74176...
View ArticleForum Post: RE: OMAP-L138 DDR2 JESD79-2A signal levels
FrancoisFor the DDR signals, the overshoot should comply with the standard. A PCB designed compliant with the TI DDR PCB specification will meet overshoot requirements and should not cause any problem....
View ArticleForum Post: where to post post the FIR filter design Issue with CC430F5137
Hello,I am working with the FIR_filter design using CC430F5137 and CCS5.The filter designed is working but it is giving out the values more than the max ADC can read like the filter is giving ouuput...
View ArticleForum Post: MEMORY INCREASE FOR A C5535
Hi, Im using a TMS320C5535 eZdsp for a detection algorithm. My vectors exceeds the memory's limit. Can i use the SD CARD for increase the vector's memory? Exists other way for increase memory for the...
View ArticleForum Post: RE: Twin die DDR3 supported in C6678?
g.f.As you saw in that other post, the debugging was never concluded. There were layout issues that complicated the analysis. I requested an update on this design debug.The C6678 does support 2 ranks...
View ArticleForum Post: RE: 6482 CSL support
Xining Yu,Please assume you have a C6455 and try to move forward. It really does not matter for the testing and use of this board, as I said above:"The same CSL will work for any common features of the...
View ArticleForum Post: Keystone II SGMII signal levels
We are connecting an SGMII port of the 66AK2H12 to a 1000Base-KX port across a VPX backplane thru AC coupling caps. The 1000Base-KX is a 1.25Gbps SERDES version of gigabit Ethernet (per IEEE...
View ArticleForum Post: Which Starterware ?
Is there a "Starterware" (ie Bare-Metal) development package to use with the Beagleboard xM ? That board uses the DM3730 processor so I'm confused with which (if any) of the Starterware sets will work...
View ArticleForum Post: RE: C6748 LCDK MMC/SD0 bootmode
Srinidhi,This needed to be a new thread instead of being added to an answered thread. New threads are much more likely to get attention for people other than those on the original thread.Have you...
View ArticleForum Post: RE: dm8168 audio
Hi Vengad,The LM4549 uses open source AC'97 driver. Feel free to contact me directly on this at ryanlin@ti.comRyan Lin
View ArticleForum Post: RE: Is it possible to control upp from arm?
Thank you.I will do more investigation and come back later.
View ArticleForum Post: RE: XIP_MUX0 boot problem
hello , Pavel[quote[quote user="Pavel Botev"]Have you enable/select these pins in the PINCNTLx MUXMODE bits?[/quote]since the evm nor flash is 64MB, my costomer board nor flash is 128MB, I add...
View ArticleForum Post: RE: New Custom AM1802 Board Boot from SD Card
OK, I see that now. I looked back on some of the other debug gel outputs and I see all of them are this way except for 1 that was captured on 2/2 @ 11:30. I think that is when we decided to not let...
View ArticleForum Post: RE: Current Consumption on 0.9V in DM8168
This supply can consume up to about 5mA so make sure that your solution can support at least this.BR,Steve
View ArticleForum Post: C6472 Atomic Access Monitor - SL2RAM Questions
1) When using the C6472 AAM instructions (LL,SL,CMTL) on S2LRAM, does the state of the SMC pre-fetch matter?2) If we need to set up multiple monitor variables/addresses, is there any minimum spacing...
View ArticleForum Post: RE: singlecore bootloader --- multicore bootloader
Just to add: above code will need to be added for core 0, typically right at the beginning in main().-David
View ArticleForum Post: RE: RE: C6678 I2C Boot PG2.0 Boot
Gentlemen,Sorry to jump in, I read the thread but I am not sure what the goal here is. However, if you are going to do PCIe boot on C6678, there are a lot of working examples here already with...
View ArticleForum Post: RE: hdmi audio consuming too much data
Never mind. I got it working by increasing the size of my audio buffers. It works fine now other than the occasional underrun. I still need to get the underruns figured out.
View ArticleForum Post: RE: Looking for Easy way to Boot TMS320C6672
Joe,SPI is fine too. I would suggest you read the bootloader user's guide to get more information:http://www.ti.com/product/tms320c6672Click "Show More" under "User Guide", then click, "DSP Bootloader...
View ArticleForum Post: RE: TMS320DM8168 JTAG connection
Make sure that the M3 clock is enabled and running.As a side note why do you need to access the M3? This processor is not intended to be user accessible.BR,Steve
View Article