Forum Post: RE: source code of ROM Ethernet bootloader - K2H
Hi Rahul,Thanks for your reply. Facing problem while running bootloader code on K2H platform. Earlier we successfully able to boot on C6678 device and at present we are using the same (C6678's) RBL...
View ArticleForum Post: RE: Kernel does not start after upgrading keystone U-Boot
Justin,I don't see the issue on my Rev 1.1 EVM. I attached my logs and commented in the attached file. You can see that I first programmed 3.0.0.11 u-boot and then using it to boot up 3.0.3.15 kernel....
View ArticleForum Post: Comments on how hot TI's TMS320C6657 DSP gets (Power Consumption)
Hello, I am planning on using one TMS320C6657 on my next design. I'm expecting to use the following configuration:Operating Frequency: 800-MhzDDR3 DisabledSRIO Enabled: 1 Lane, Mode DIO, % Utilization...
View ArticleForum Post: RE: Error with RTS Library on K2H Cortex-A15
Keith,May I ask if the SIMD and VFP extensions are enabled before you call the floating point functions please?The A15 Technical Reference Manual (TRM) mentions "From reset, both the Advanced SIMD and...
View ArticleForum Post: Looking for TMS320C6657 Pin File used to make schematic symbol
Hello, I use Mentor Graphics DxDesigner to make my schematics and would like to make a symbol for the TMS320C6657. I cannot find a pin file or symbol information that I could use to make this schematic...
View ArticleForum Post: RE: [TMDSEVM3730] TVP5146 capture issue
Dear Cvetolin,For test case of android GB, I did not port camera module at android GB. It was Ginger Bread image of original SD card included in TMDESEVM3730 (AM/DM37x Evaluation Module, Mistral).I...
View ArticleForum Post: RE: What's the maximum H.255 Encode/Decode capability of C6678?
Have any updated H.265 performance data for C6678?We need to evaluate it.BR.
View ArticleForum Post: exit exception
hi all,any one can answer the following thread question?http://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/717/p/314021/1093698.aspx#1093698tks
View ArticleForum Post: Is there any specific code in TMDXEVM6657L EVM boot code?
Hello.I tested Ethernet communication with TMDXEVM6657L EVM board, based on \ti\pdk_C6657_1_1_2_6\packages\ti\drv\exampleProjects\EMACBenchmark_exampleProject.And I designed my board and tested with...
View ArticleForum Post: RE: Operating C5515 in low power mode
Well, if you are just considering power, then it is easy to conclude from Table 1-31 in System User's Guide that RTC only mode is better than IDLE3 since all power domians are still on in IDLE3...
View ArticleForum Post: RE: Interfacing TMS320C6670 to an external ADC
Hardik,Please clarify your expected data throughput. You mentioned: "need at least 4 channels on the ADC where I will input 20-30 Khz four analog signals ... simultaneous sampling and the sampling...
View ArticleForum Post: RE: datasheet for atw310 sensor in C5515 Fingerprint development kit
Hello,The manufacturer for ATW310 sensor has been acquired and is no long selling this device. We no longer support the sensor code, as the sensors are no longer in production.I recommend contacting...
View ArticleForum Post: RE: DM814x video DAC power-down
Pavel-Thanks for the response. What you describe above (i.e. bits 25 and 24 mapping to DAE1 and DAE0) is pretty much what we'd figured was the case based on a reading of the code.In actual practice,...
View ArticleForum Post: RE: C64x vlib installation error
Also, whats the process to uninstall. I don't see it listed in my add/remove programs and nor is these an item in my Start menu for TI.Cheers
View ArticleForum Post: RE: unable to receive data to ttyS1 on XTCIEVMK2X board
There is a mux that controls the routing of the UART1 to the expansion header. You actually have to setup the device GPIO[11] to be an output AND drive to GND to get the MUX to function properly....
View ArticleForum Post: RE: C6657 SmartReflex Timing
Hi Dave,The VID value will be transmitted after the reset(PORz+RESET+RESETFULL) has been released. The delay from the rising edge of RESETFULL to the VID value will vary based on boot mode. In addition...
View ArticleForum Post: RE: Comments need on I2C spru877e
Thank you, Sivaraj I find some explanations of MMRs in sample of SmBus driver state machine, that you post some years ago.
View ArticleForum Post: RE: NDK / NIMU support for both EMAC interfaces
Ralf,Thank you for sharing the code, first of all. I just can't understand how different MAC addresses fit the picture. I mean, with normal switch we should have a single MAC for the device and I...
View ArticleForum Post: RE: Intermittent HDVPSS Firmware Load Failure on EZSDK 5.04
Jon,Thanks for you suggestion, yes I will post a new thread on this problem, cause right now most the problem I met were related to hardware, my custom board have 1GB DDR3 as 8168evm board, same...
View Article