Forum Post: RE: About C6670 PCIe Device ID
Yes, they can program 0xB005 to it.Regards, Eric
View ArticleForum Post: TVP5158 chip ID regs
We are having problems reading The Chip IDs of the TVP5158 in order to verify operation. We have followed the datasheet according to the reset requirement and have verified the I2C layer protocol. Both...
View ArticleForum Post: RE: DM8148 simultaneous video in NTSC, RGB ( VID 0 ), and HDMI...
Hi, I need to do something similar, I have a GUI created using qt and I need to display the same GUI and its changes in both, HDMI and SD at the same time, I also tried to tie both but the image get...
View ArticleForum Post: RE: optimizing C66x PCIe transfers for multiple cores
Jeff,Since the PCI Express serial bus is a dual-simplex bus, you can have both inbound and outbound traffic on the bus concurrently without substantial performance degradation. And EDMA will always be...
View ArticleForum Post: RE: QT Application on two frame buffers on two displays on dm814x
Hi ksr, I need to do something similar with QT, one of my outputs in an HD monitor and the other is an SD monitor, were you able to get it working? did you need to scale the graphics pipeline for...
View ArticleForum Post: RE: Idle / disconnected Hyperlink bus VDDT1 current draw
Bill (TI),Do you have enough information to solve these questions? Thanks!Janice
View ArticleForum Post: RE: CSL Libraries and Bitwise C code
The option is also known as "--preproc_only," so look for that. I don't have a copy of CCS 5.5 handy. In CCS 5.4, it's under "Advanced Options" > "Parser Preprocessing Options". If your source...
View ArticleForum Post: RE: SRIO doorbell interrupt cannot be trigger
Hi,Travis:As you said,SRIO routing and configuration is no problem.Meanwhile,interrupt routingand configuration is also ok .Since,Everything is no problem,What's the matter?
View ArticleForum Post: RE: C6748 SERIAL BOOT BINARY QUESTION
Hi Shankari,In that case the customer will need to modify the serial Flasher so that it is more of a loader to just load the code into SRAM. Is that correct? Looks like the source code is there an...
View ArticleForum Post: RE: 8168 FileRead- Encode- FileWrite Usecase
Share the console logs and logs of Vsys_printDetailedStatistics and Vsys_printBufferStatistics
View ArticleForum Post: RE: 8168 resource allocation
Enable exception dump as described in these posts and share the crash dump file and the .xem3 http://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/717/p/250529/876689.aspx#876689...
View ArticleForum Post: RE: Oddities in dMAX that works with McASP on 6726B
Thank you, Sivaraj!I fined error. Frequency of SYSCLOCK1 was too low.
View ArticleForum Post: change AR8031 to 88E1111
I designed my custom board that refer to MS_TI_DM814x_BB_REVD_SCH in MISTRAL. And I changed PHY chip (88e1111). When linux boots up, the net does not work. Anyone help me please, What should I do?
View ArticleForum Post: DDOTP4H
Is there any instruction that add the results of the DDOT4H? that is the upper 32-bit + the lower 32-bit of the long long resultsRegardsNaim
View ArticleForum Post: RE: rare case: "Overflow detected on VIP0"
There is no PG 3 for 816x device.Last revision is 2.1. PG 3 exits only for 814x
View ArticleForum Post: Difference between 'unitTest' and 'pktRouterTest' of NWAL drivers
Hi all,I am using XTCIEVMK2X - TCI6636K2H EVM. Developing environment is: CCS ver 5.4.0.00091 MCSDK Packages: 3_00_01_12I can see in the test folder of NWAL (...
View ArticleForum Post: RE: DM365 with new NAND (Samsung NAND 128MiB)
Hi,Can you validate the same behavior on a different board? If this same behavior is seen the we need to see why flash_eraseall is marking every block as bad. This could be an issue in the NAND driver.
View ArticleForum Post: RE: Scrolling bootsplash when using u-boot with LCD
Hi Devin,If you can spare a set of hardware, we can solve the issue for you.
View ArticleForum Post: RE: Re: USB detection in DM8148
Debasish,Can you try first on an DM8148 EVM and see whether host works properly or not. Then let's try to debug your board's issue.
View ArticleForum Post: RE: how to flash nand flash via Gel file and nand-flash-writer.out
Looks like your LISA mapping is not proper. But I'm currently not sure what is the right value as I'm not clear about your memory configurations. [quote user="vivek gupt"]what is NAND_BASE...
View Article