Quantcast
Channel: Processors
Browsing all 124437 articles
Browse latest View live

Forum Post: RE: Trying to figure out the i2s to soc

HiI have additional questions concerning this issue. I was working on other tasks so I am only recently back on this task. I am trying to confirm some additional information. Again I am trying to drive...

View Article


Forum Post: RE: How to deal with the situation in which one DSP connects with...

[quote user="steve zhang"]If DSP0 has two hyperlink interfaces.such as hyperlink0 and hyperlink1.I let hyperlink0 connect with DSP1 and let hyperlink1 connect with DSP2.Doesn't it?[/quote]Yes.[quote...

View Article


Forum Post: OMX failing to restart a scalar component on DM8148

HI,We are trying to create a video player that supports various video input resolutions on a DM814x EVM using ezsdk 5.05.02.00 gst-omx plugins. The project works fine but after undergoing our endurance...

View Article

Forum Post: RE: About C6678 DDR address space

You are right, that is the full 8GB address range for DDR3.We only publish the default 2GB physical range in the data manual. The user is expected to extend the address range beyond default using the...

View Article

Forum Post: RE: Performance of H264 Decoder in DVRRDK4.0

There seems to be no performance issue. It is showing same fps for all channels. Check if the attached patch helps .(Please visit the site to view this file)

View Article


Forum Post: RE: Problem capturing video imaging using LCDK6748 from a Leopard...

Hi VaishakI can help you, finally my application works very well, but not now, i'm very busy right now, maybe the next week.But your first step is getting the initial commands for the sensor OV2640, if...

View Article

Forum Post: 66AK2H12 hardware guide and power pins

The revE datasheet says to leave the Vpp pins unconnected, but eval board has them connected to 1.8V.   Which is correct?We're not using USB on the 66AK2H12.   I was told early that VDDUSB, VP, VPH,...

View Article

Forum Post: Pin Mapping Tools

Hello, can anyone tell me if the following requires the Pin Mapping Utility: TMS320C6678TMS320C6657joe

View Article


Forum Post: Problem with code composer using a TMS320C5535.

Hi, i am using a tms320c5535 for audio processing and  based in one sample program, i did this code:SET.c:#include "stdio.h"#include "ezdsp5535.h"#include "ezdsp5535_gpio.h"#include...

View Article


Forum Post: RE: DSP memory space data/program

Q1: Yes, the page 0/1 in the MEMORY directive are the same as the program memory mapping.  Yes, page 0 means program data and page 1 means data memory.Q2: No, the same address in PROG and DATA are not...

View Article

Forum Post: RE: AIF2 Timer Precision

Hi,the AIF2 AT should work correctly on nano second level if your clock and MMR configuration is correct.Please check your ref clock frequency, AIF2 SERDES PLL setup and AT configuration again.you can...

View Article

Forum Post: RE: USB: usb_rx_ch_teardown 1057: teardown Desc not found

From Ravi: diff -r 5a9a16c59095 linux-2.6.37/drivers/usb/musb/musb_host.c--- a/linux-2.6.37/drivers/usb/musb/musb_host.c Tue Dec 17 18:51:59 2013 -0700+++ b/linux-2.6.37/drivers/usb/musb/musb_host.c...

View Article

Forum Post: RE: Problem with code composer using a c5535.

where can i find this linker command file ?

View Article


Forum Post: RE: How to set SW1 switch on OMAPL138LCDK for emulator connection?

Hi,I would like to use emulator XDS200 to debug a small project. I do not understand which boot mode I should use, see below table. Could you explain it to me? Thanks,Switches (SW1)Switches 1-4 on SW1...

View Article

Forum Post: RE: TCI6638K2K: mutal exclusion between DSP and ARM

Vesa,The HW Semaphore should be accessible via the ARM side, I'll ping someone from the ARM SW side to comment on what code source we have available for this.Kesytone decides do not provide a HW...

View Article


Forum Post: RE: powering options in ezdsp5535 eval kit

Hello Aswin,   Yes,  Jumper JP2 is the power source select jumper. When this jumper is shorted the C5535 eZdsp can be powered from the C5535 USB interface (J1). This jumper is shipped in the  shorted”...

View Article

Forum Post: Yocto Project and TI DSP Libraries

Hello,  I want to integrate IMGLIB and VLIB packages into my custom kernel build using Yocto Project to BeagleBoard. I have researched throughout internet but I cannot find anything. Could you please...

View Article


Forum Post: RE: [Urgent] Confirm the XF status after waking up from RTC-only...

Kaka-san,XF is a "1" after reset. This is stated in the Pin Behavior at Reset section under the SYNCH X->1 Group. In addition, I ran the RTC_Only verification code which also shows XF is ON after...

View Article

Forum Post: RE: Why are C6670 DDR3 address pins A15/14/13 connected to...

J,These NC pins on this sixze memory device are high-order address bits on larger devices.  These are unused when accessing smaller memories.  This allows the memory to grow on the board without...

View Article

Forum Post: RE: Idle / disconnected Hyperlink bus VDDT1 current draw

Hi Bill,I'm afraid I don't really have an answer for you. The VDDT powers an internal linear supply so there will always be current flowing, even when the Hyperlink is not in use. We don't measure the...

View Article
Browsing all 124437 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>