Forum Post: RE: Measure PA performance and throughput
The pa_getTimeStamp returns 48-bit system timestamp, that is for PA subsystem, the PA PLL clock is set by Linux. There is no load status for the PA.Regards, Eric
View ArticleForum Post: Encoding two 1080I_50/60 using ezsdk_dm814x-evm_5_05_01_04
Hi TI,We are using DM8148 based custom board.Now we need to encode two 1080I_50/60 in parallel.When I tried this with my application it is giving me the insufficient resources error : got event***...
View ArticleForum Post: RE: DM368 AEMIF's WE#
Hi Eason,I am seeing the same phenomenonEM_WE (pin J15) & EM_OE (pin J19), both pull-up to 3.3V through 10k resistor, are showing two different behaviours: EM_WE will "stuck" at around 2.2V...
View ArticleForum Post: RE: DM385 : IPNC usecase to send and display YUV frame from A8 to...
Can any one help us to understand the problem ?Or, Is there any use case to test the USB camera ?
View ArticleForum Post: RE: How to design the Data communication path and Message...
The IPC SRIO Transport which was recommended has outstanding bugs, the SRIO interfaces are fine of...
View ArticleForum Post: RE: Communication between Devices(XTCI6638) using HyperLink or SRIO?
As Iding replied to both threads, and both are even located in the same forum ... no need to cross post.
View ArticleForum Post: RE: [HPI interface help]how could i use hpi to access the...
if dsp receive the data coming from the host,but the start address is not my defined address.why?
View ArticleClik here to view.
Forum Post: RE: C6657: OpenMP example fails
hi Chris,thank you for reply!I got the error above (screen shot): unresolved symbols: #10234-D.The unresolved symbol ist "omp_qmssGblCfgParams".I found this variable in Navigator.c (see below), but do...
View ArticleForum Post: Read and write NOR flash on TMCXEVM6657LE evaluation board
Hi, I'm searching some examples or test code of the TMCXEVM6657LV evaluation board where I can write the data (e.g. a block of 200KByte) to the NOR flash (N25Q032A11ESE40F) and read data from the NOR...
View ArticleForum Post: AM3874 framebuffer from u-boot
Hi!I'm reviewing the code used in uboot in order to display a logo on screen. I've seen the code is based in a firmware binary loaded by uboot, see the 'vpdma_firmware[]' array from...
View ArticleForum Post: RE: Camera Interface With Am1705
Sanket,I do not think video port(VPIF) is avilable in AM1705 for camera interface, Please refer the datasheet of AM1705http://www.ti.com/lit/ds/sprs657d/sprs657d.pdfFor USB Interface of 3G, refer the...
View ArticleForum Post: DM365: usb working on full speed?
http://e2e.ti.com/support/embedded/linux/f/354/p/161124/1061660.aspx#1061660
View ArticleForum Post: pcie interface between dsp and fpga
Hi,We are implementing PCIe interface between DSP(Root complex) and FPGA (End point.) in our custom board. From root complex how can we know the bus number to which the end point is connected. How...
View ArticleForum Post: RE: MPEG4 SP of DVSDK3.0 for OMAP3530
Hi Gerry,I'm not sure that I understand your question correctly but I can share the following information about the MPEG-4 Simple Profile (SP) level:The MPEG-4 Part 2 (formally ISO/IEC 14496-2) has...
View ArticleClik here to view.
Forum Post: RE: OMAP-L138 SATA without cable.
Parry Admire,Welcome to the TI E2E forum. I hope you will find many good answers here.In addition,You can find some details through the TI.com documents and the TI Wiki Pages.Be sure to search those...
View ArticleForum Post: RE: h264 file decode and display to LCD problem
It should be set in VDEC_BUF_REQUEST_S parameter of Vdec_requestBitstreamBuffer API.You should populate the correct channel ID when requesting bitstream buffersRefer...
View ArticleForum Post: RE: How to set SCD Output ChannelID to 0~3?
Hi Sivagamy: thanks very much! Ok. I will try it. But i another question, I set resoluation is 704x576, how can i get frame data? I add log in scdLink_alg.c, function: AlgLink_ScdalgProcessDatato...
View ArticleForum Post: RE: Capture encode problem with DVRRDK 04.00.00.03
Hi,Effectively, I have a problem with the uboot.I have rebuilt it and I boot with it now.I have done the modification int the file utils_encdec.c.When you say invoke link control cmd to modify the...
View ArticleForum Post: RE: OMAPL138 kernel error
HI le Lemon,From the log file, it seems to me that your kernel is trying to mount the YAFFS/YAFFS2 file system from NAND Flash.Using a wrong YAFFS image may also lead to errors like this. For more...
View Article