Forum Post: RE: Why C6657 Ethernet interface speed is very slow(100kbps)?
Xiao Gang,We're afraid that we cannot access to the datamanual of them. We don't know differences between them.Regards,Atsushi
View ArticleForum Post: RE: Unexpected HWI is triggered
It was my mistake.I found that I enabled unused interrupt, i.e. HWI4.I disabled HWI4 and the code run.Dongseung
View ArticleForum Post: look up nsp of 6614
hi. I want to add the ndk on 6614.but the nsp only support 6748. building is failed:error infoundefined first referenced symbol in file --------- ---------------- NIMUDeviceTable...
View ArticleForum Post: What's the difference between global region and shadow region in...
What's the difference between global region and shadow region in EDMA3? I use C6657.I write a driver for global region, it works well. But when I change region to shadow region1, it didn't transform...
View ArticleForum Post: RE: Can not find H265 (HEVC) Encoder Demo in mcsdk_video_02_02_00_23
Thanks for your help.
View ArticleForum Post: RE: For intermediate potential of EVM-1V5
Hi, AmitThank you for reply. I will answer a few questions for you.I created the connection map of the power pin of DM8168.A list of all the power that is connected to the DM8168.Please check the...
View ArticleForum Post: C6747 MCASP0 problem with 96K sample/sec in slave mode.
Hi ,I am using C6747 with OMAP L137 EVM board.Test condition is- OMAP L137, CCS 5.4- EVMBOARD: I2S(input) (slave) -> MCASP0 -> Loopback copy Task -> MCASP0 -> I2S (output) (slave)I am...
View ArticleForum Post: RE: For SD timing of EVM
Hello.I do not know where you are pointing the timing in the waveform above .Therefore , I have created a support documentation.I'm attach the supplementary material .(Please visit the site to view...
View ArticleForum Post: RE: board cant get kernel image
and there is a also fault in my bootargs.in that I always write console=ttyS0 instead of ttyS2
View ArticleForum Post: how to use NANO-X in OMAP L138?
helloI want to know how to use NANO-X in my OMAP-L138.I download sourece from microwindows.org and compile but some error .how cam i comile for arm.when I change in config file for arm and give...
View ArticleForum Post: RE: Puzzled with the configuration between BAR and IB_BAR of...
Hi, Thanks a lot, I get it. Here is another question : why " uint32_t *prtReg = 0" is right ? I thought a pointer should point to a actual address. Does it also means " uint32_t...
View ArticleForum Post: Frame Buffer driver support in DM385 IPNC RDK 3.5
Dear all,I'm using DM385 EVM Board with IPNC RDK 3.5 SDK. Previously we used latest EZSDK and tested the all the video outputs using frame buffer driver. Because of some constraint, Now we are using...
View ArticleForum Post: RE: TIWL1271 and MCBSP interface on OMAP3530EVM.
Hi Krunal,I'm having an issue interfacing MCBSP3 to record voice data from MIC.I have made changes at the PCM level.I need to configure twl4030 to be a master and MCBSP as the slave.I know the changes...
View ArticleForum Post: RE: AM3874 custom board : Data written into the Nand flash did...
Poh,[quote user="Poh Boon Teo"]must I name the file to MLO before I flash in the code??[/quote]No, MLO is used only for SD boot. For NAND boot, you should use ti8148_evm_min_nand and the generated...
View ArticleForum Post: RE: Using the C6746 UHPI_HAS pin
Hi Sunil,For correct operation, is not it allowed for UHPI_HAS to be Low in a period when UHPI_HCS and UHPI_HDS1 and UHPI_HDS2 are High?Best regards,Daisuke
View ArticleForum Post: RE: How to run successful OMAP-L138 UPP capture
Duy-Ky,Please have a look at the below thread. This thread may help you.C6748 UPP Receive:http://e2e.ti.com/support/dsp/tms320c6000_high_performance_dsps/f/115/p/108839/384905.aspx#384905
View ArticleForum Post: RE: RDK4.0 SYSTEM: Attaching to [HOST] ...
Set vmalloc=476M in your kernel bootargs as documented in the DVR RDK 4.0 2G memory map user guide
View ArticleForum Post: RE: ti8147 hangs on attempt to use vpss after resume
Devin,[quote user="Devin Heitmueller"]For my information, are you currently testing with the code change you mentioned in your response on Aug 14th where you commented out the call to...
View ArticleForum Post: RE: channel at same hdvicp coprocessor is not working
Logs indicate HDVICP1 is hung. You can confirm this by adding below code indvr_rdk\mcfw\src_bios6\links_m3video\codec_utils\src\iresman_hdvicp2_fwif.cXDAS_UInt32 HDVICP_Wait(IALG_Handle handle,...
View Article