Forum Post: RE: EDMA3 UART/block transfer on L137
Hi SivarajThanks for your answers. I was in vacation that's why I didn't write back earlier.An increase of the UART FIFO trigger level would help to solve this problem that is true but it leads...
View ArticleForum Post: RE: How to reset/erase u-boot environments?
Hi Zhe,yes, using the same "setenv" or "Set" commands you can delete the u-boot environment variable by following the syntax given belowsetenv ipaddr 10.100.2.202 --- > will set the ipaddrsetenv...
View ArticleForum Post: RE: u-boot "reset" command hangs
Hi Rajasekaran,In our design, reset out pin is a no connect. Which reset pin should I probe?Will check for activity on the boot pins when I get some time.Cheers,-raja.
View ArticleForum Post: RE: [DM814x] support for sdhc UHS-1?
Hi Hayden,I think "UHS-1" is the same as "UHS-I", right?It seems that DM814x/AM387x device does not support SDHC UHS-I cards. See the thread...
View ArticleForum Post: RE: 6678L multicore programming
Hi Allen,Sorry to disturb you, but I hope you're still looking up sometimes in this forum.Currently I'm trying to use master-slave module, I saw this post and wanted to run the attachment you uploaded,...
View ArticleForum Post: RE: Access DSP memory from a Host PC through PCIe (c6687).
Hi Shlomit,I think that is should work, please check the sprugv8c.pdf -KeyStone Architecture DDR3 Memory Controller User Guide table 4-1/4-2 there are some registers where you need to Unlock Boot...
View ArticleForum Post: DM3730 - jitter on the DSS_PCLK signal
Hi,We use DM3730 to DAC (THS8200) for VGA output.We get defects on the screen, due to jitter on the DM3730 pixel clock DSS_PCLK.We use the "display controler" driver on DM3730.How to reduce this jitter...
View ArticleForum Post: RE: Psia not working
Can you please check with v3.1 release if this issue persists? as we checked with v3.1 and we could not see this issueAlso, can you please share the log to get more details on the paramters and usecase...
View ArticleForum Post: ipnc368 rs485(uart0) read always returns 0
Hi, everyoneIn ipnc368 I programing the rs485(uart0, sn65hvd11dr rs485 transever) to communication with my PC.when i write to UART0,serial assistant can recive data ok.but when PC transmates data to...
View ArticleForum Post: RE: Serial flash utility - OMAP L137
Hello Shankari,I have pasted the console output after successful completion of "ERASE" operation. We want the below to be redirected to a file (.txt)....
View ArticleClik here to view.
Forum Post: RE: About MJPEG encode quality
Hi Badri,Please see the attachment, it's configuration is as followsResolution: 1920x1080,Target bitrate: 1MbpsqpInint: 2
View ArticleForum Post: OMAPL137/TMS320c6747
hii am very new to DSP ,rite now working on OMAP L137/TMS320C6747 EVM ,upto now got soultion how to start with CCS V3.3 ,and i had test the led program successfullynow its time to make a move towards...
View ArticleForum Post: Building example projects in PDK of MCSDK using CCS
Hi,We are trying to run some example tests on TCI6638K2K EVM. But we are unable to build the example projects present in the PDK. Can soke point to the correct method of building the example...
View ArticleForum Post: RE: Regarding next EZSDK 5.03 and Gstreamer lib
Hello Baz,Could you provide more details, please.What is the software release that you are using here?For capturing are you using gstreamer?What is your video source and how is connected?BRMargarita
View ArticleForum Post: Please suggest us a IP network camera manufacturer that uses DM...
Hi Everyone,We are searching for IP Network Camera manufacturers that use DM 365, 368 or 385 chip inside with "F" ending i.e. with imbedded face detection. We have searched everywhere but only...
View ArticleForum Post: RE: DM8148 - McBSP's Sample Rate Generator & AUXOSC Clock
Hi Pavel,Thank you for your answers.First, I'll summarize my results in short: I. External oscillator is connected to AUXOSC clock. II. I've configured PLL_AUDIO, PRCM, Sample Rate Generator.III....
View ArticleClik here to view.
Forum Post: RE: How to config the clock for uPP?
Oh, sorry, I use mode, the figure should be this one:
View ArticleForum Post: RE: gstremer rtsp server support in ezsdk
Hi,I used following pipeline to stream to a particular ip and particular port.gst-launch omx_camera ! 'video/x-raw-yuv,format=(fourcc)NV12,width=1920,height=1080,framerate=(fraction)30/1' ! omx_h264enc...
View ArticleForum Post: RE: How to Run X-app on TI-DM814x once the X-Server is Setup
Hi Pavel ,please find the error log of /usr/local/XSGX/var/log/Xorg.0.log below[4035895.901] drmOpenDevice: Open failed [4035895.901] drmOpenDevice: node name is...
View ArticleForum Post: RE: EVM is not booting from Original SD Card
Pavel, Yes you are right, minicom is working fine and flow stuck at "MMC: OMAP SD>MMC: 0" line. I haven't change any thing to u-boot source code and wutomatically created and size of SD card is 8...
View Article