Forum Post: RE: Can't change pin mux in Linux
Hi Badri,My customer find that they can't modify PINMUX reg under linux user mode, while it works under kernel mode.Is the ARM supervisor correspond to the linux kernel mode ? It looks like the...
View ArticleForum Post: RE: OMAP3 ISP DQBUF hangs
I solved the problem by myself. I needed to do ioctl STREAMON after ioctl QBUF.Regards, Tom
View ArticleForum Post: RE: Asking to correct a bug in the McASPEcho_dspL138 project...
Mukul,Sivaraj K had asked for some time to provide an update ASAP, but you try to disavow his statement. Are you authorized from him for this action or you are simply a defender of corporative...
View ArticleForum Post: RE: REISZER OVERFLOW OCCURED
Hi Zhouran,When using vertical mirroring and changing the sensor exposure, I get a resizer overflow and the image freezes and I can't see any video until I restart the usecase.In normal display mode...
View ArticleForum Post: RE: USB Webcam with OMAP-L138 LCDK
Jacob,Welcome to the TI E2E forum. I hope you will find many good answers hereIn addition you can find some details through the TI.com documents and the TI Wiki Pages.Be sure to search those for...
View ArticleForum Post: RE: The SPI flash utility given in the...
Debasish,Can you share all your steps?Is Linux running on the Cortex-A8 ARM? The GEL file assume there is no OS running and tries to manipulate registers used by the OS. Make sure there is no SD card...
View ArticleForum Post: RE: framework for DM8148: dvrrdk or ezsdk?
Hello,In DVR_RDK you can access and modify the M3 source code, if needed. Check also the below thread:http://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/717/t/166685.aspxBRPavel
View ArticleForum Post: RE: DM386 encode HD video on 1080i loses frames
I am using the DVSDK, where to set the extented Paramers in the DEMO? There is not "IH264VENC_Params" or "IVIDENC1_Params" in the DEMO. can you give me a demo that including the...
View ArticleForum Post: How to run the demo application in ipnc_app for IPNC_RDK_3.5
Hi All,I was working on IPNC_RDK_3.5 version on DM365 board.I can able to make kernel image and filesys, with those I can bring the target also. once board is coming up system_server & boot_proc...
View ArticleForum Post: Early-life failure ratio(ELFR) of TMS320VC5501
Hi all,I need the data associated with the TMS320VC5501.Would you have any information about the following data?・Data of the early-life failure ratio(ELFR).Please tell us your data by all means.Regards.
View ArticleForum Post: Soft error rate(SER) of TMS320VC5501
Hi all,I need the data associated with the TMS320VC5501.Would you have any information about the following data?・Data of the soft error rate(SER) caused by neutron emission.Please tell us your data by...
View ArticleForum Post: SER (caused by alpha particle emission) of TMS320VC5501
Hi all,I need the data associated with the TMS320VC5501.Would you have any information about the following data?・Data of the soft error rate(SER) caused by alpha particle emission.Please tell us your...
View ArticleForum Post: Single event latch-up(SEL) of TMS320VC5501
Hi all,I need the data associated with the TMS320VC5501.Would you have any information about the following data?・Data of the single event latch-up(SEL) caused by neutron emission.Please tell us your...
View ArticleForum Post: RE: C6A816x Ethernet Boot MAC address
Hi Marc,If we want to use our own MAC address. How could I do this?By writing to the MACADDRLO and MACADDRHI registers (RW) in the EMAC Control Registers ?Writting MACADDRLO and MACADDRHI will change...
View ArticleForum Post: RE: Stack dump when capturing video for the first time
Hi Tamo,I found some info in the below e2e thread, please have a look, might be in help:http://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/717/t/153250.aspxBRPavel
View ArticleForum Post: RE: How to disable/invalidate cache holding MSMCSRAM
Geoffrey,yes it is possible. It's not straightforward as it involves memory address translation.You need to configure the XMC something.There are threads on the forum about that.Clement
View ArticleForum Post: RE: c6748 hpi boot (Cannot Boot Up)
Hi Sam,Please refer the wiki link to create the secondary boot image with entry address....
View ArticleForum Post: RE: Dynamic display switching from LCD to TV on DM3730
Hi Shulev,We tried the command as suggested by you. The display is cropped to its left as shown in the pic above. The below commands will shift the display to the cropped display to right.Commands...
View ArticleForum Post: RE: Interfacing TMS320DM365 with OV7955
Hi,Sorry for late reply.Please install ImageTuningTool provided with you IPNC, this will give you the options to YUV as well as RAW data in web GUI.Follow the user guide of ITT(ImageTuningTool).you can...
View ArticleForum Post: RE: How to set the display order? Emergent ! Thanks !
Hi Badri, Thanks for your reply ! I have done the first step. Could you give me some advices about how to set the swms background fill color to transparency ?Best regards!
View Article