Forum Post: DM8148 - Mcbsp Driver For Dsp
Hi,I'm working with DM8148 EVM, I would like to work with the Mcbsp from the dsp.I found PSP package for C6748 which has Mcbsp driver. However, this driver defines RCR as Uint32, this contradicts the...
View ArticleForum Post: RE: DM8168 Lossless streaming using Gstreamer
Hi Margarita,Thank you for the inputs and the example pipeline.But as I mentioned in my post dated 09 July 2013, my requirement is to have a lossless streaming.The pipeline you suggested above is using...
View ArticleForum Post: RE: question about osd when input frame/field data
OSD supports different data format for each channel. Why do you think it is impossible to do two channels with different data format
View ArticleForum Post: RE: [m3vpss ] Unhandled Exception:
Pls refer this post http://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/717/p/277385/971514.aspx#971514 and generate the log dump of exception for analysis.
View ArticleForum Post: RE: How to run IPC based image processing demo application on a...
Looks like you've built w/o a valid linker command file to tell the linker where to put the data. So it would naturally start at 0x0, but there's no valid memory space there. You need a valid linker...
View ArticleForum Post: RE: c6654 timers keep running when core halted
Steven,Thanks for looking into this. Have you been able to find anything yet?Thanks,Mark
View ArticleForum Post: RE: OMAP-L137 ping failed, Ethernet doesn't work
Thank you Rajasekaran, My u-boot environment settings and other configurations were just like you told me when I gave the first try. I guess there were something else I missed. So I started over and...
View ArticleForum Post: SPI1 issue - spi_write hangs on OMAPL138 LCDK
Hi,I am using OMAPL138 LCDK (Hawkboard) with custom LCD hardware. LCD is interfaced over 16 bit RGB interface and 3 wire SPI1 configuration.I have done necessary modification in kernel for SPI1 support...
View ArticleForum Post: RE: How to change hello_openmp_evm6678 to 8 cores
Uday,ok.(I notice this occurs because ccs start to build automatically the workspace and there it hangs out)Maybe you could help me with this.I actually want to debug the simple hello_openmp_evm6678...
View ArticleForum Post: Does DM8168 support video encryption
as title. Is video data encryption supported in DM8168 firmware with DVR RDK 4.0?Thanks.
View ArticleForum Post: RE: NDK hang after 20 minutes running
Hi, EricThanks to your help that I find out the board I am using is EVM v1.0, which is a Beta test version. I switch to a new board (Rev 3.0b). it runs so far so good!. again I will do a overnight test...
View ArticleForum Post: RE: What are the sys_int and host_int refer to in the 6678?
I think the diagram is referring to C6670 interrupt topology, in which CIC0 (chip level INTC0) has 208 system events input.For the host interrupt output from CIC0, the maximum event number connected to...
View ArticleForum Post: RE: LTE PHY layer
I am in the US. I will try to call you later today. Regards,Hector Rivera
View ArticleForum Post: Is low video resolution encoding supported by DM8168?
Hello, Recently, we found 360*240 video resolution doesn't seem to be supported by Enclink of DM8168. We got the Enclink assertion message. Is low video resolution supported by DM8168?Per our...
View ArticleForum Post: How to open *.lib files
Hello everyone, when i build my project with differrent *.lib, the *.out file being built seems differrent too. Is there anyway to translate the *.lib files to *.c format?Thanks a lot!
View ArticleForum Post: RE: realtime data transfer with ADS1605 and TMS320C6416 /...
Chritsoph,Since your problem is not completely solved, I would recommend removing the Verified Answer flags. Personally, when I am looking for posts to read and help with, I ignore those that have been...
View ArticleForum Post: DM8148 - Mcbsp Configuration
Hi,I'm working with DM8148 EVM. I'd like to configure the Mcbsp from the dsp.In previous posts, it was written that "DSP can not access McBSP directly (at physical address 0x47000000), but it should go...
View ArticleForum Post: Linux booting problem on C6670 device
it's a long term problem.we designed our board base on c6670evm,build the ibl/linux and so on.but the board cannot booting linux sometimes,it just stopped at "booting from nor"(we select nor flash as...
View ArticleForum Post: RE: Question about capturing video from VGA interface and output...
Yong,If you go to the TI product folder for the TVP7002 you will find some example command files for various input modes.Please have a look through these setup files for one which is the same...
View ArticleForum Post: EHPI boot with switch to USE_RETA stack mode
Hi,I am using a C5510 processor that is booting from EHPI. Since the stack mode is set to the C54X 32-bit mode by the default reset vector in ROM, in order to switch to the fast 16-bit stack mode (I...
View Article