Forum Post: RE: 66AK2H EMIF16 address generation
Bill-san,Thank you so much for your strong support!It was very helpful for us.Best regards, RY
View ArticleForum Post: RE: Dark frame subtraction
I have figured out the reason,cause based on the datasheet,memory-to-memory mode doesn't support DFS,only continuous mode support!
View ArticleForum Post: RE: GIO_write wrong UART character sometimes
I have heard 6713 chip has problem that is why they stop making it, is it true?
View ArticleForum Post: Upgrading code from DM3730 to DM8148
Hello,I just acquired the EVM DM8148 and downloaded the EZSDK 5.05.02.00. I have previously developed a codec for the EVM DM3730 (DVSDK 04.03.00.06) and used the decode application in the dvsdk demo to...
View ArticleForum Post: RE: DM8148 Encoder issue (SEI message and num of nalu_type)
Hi, Please check below log.[m3video] --------- CH 0 : H264 ENC : Dynamic Params ------- [m3video] [m3video] videnc2DynamicParams -> inputHeight : 720 [m3video] videnc2DynamicParams -> inputWidth...
View ArticleForum Post: I want to transfer video via Emac from the DM8168 to another DSP...
I really don't know how to do it .Other DSP ,there is NDK,but DM8168 there isn't it ,what should I do ?please hlep me.
View ArticleForum Post: RE: Questions about The Global Variable dp_status
Hi Mukul! Thank you for your help.
View ArticleForum Post: RE: DVR SR2 section
thanks for your reply.but in my code,i just modify the value of phyaddr,do not use the variable. *(int *)Ch1BufPtr_phy=1;best regards.
View ArticleForum Post: RE: [DM8168]How to develop dsp bios program with JTAG
Hi all The problem is resolved. please see this post: http://e2e.ti.com/support/embedded/tirtos/f/355/p/339296/1186879.aspx#1186879
View ArticleClik here to view.
Forum Post: RE: DM368 resizer and Image Tune Tool
the rawfile the Bayer pattern is GRGRGRGRBGBGBGBGGRGRGRGRBGBGBGBG(Please visit the site to view this file)the video's color is OK
View ArticleForum Post: RE: I2C cannot work
Renjith,Thanks for your replay.Yesterday I have run the i2c probe, and getting the address 0x18、0x68, do you mean that command was running on i2c0? If it is, how I can do to change from i2c0 to...
View ArticleForum Post: RE: error message
Due to some reason, I couldn't paste the link publicallyCould you give me your mail ?
View ArticleForum Post: RE: DM8148 Encoder issue (SEI message and num of nalu_type)
Hi HarrisPlease check below log.[m3video] videnc2Params->nalUnitControlParams.naluControlPreset :1 [m3video] videnc2Params->nalUnitControlParams.naluPresentMaskEndOfSequence :3072 [m3video]...
View ArticleForum Post: RE: AIF2 Pi measure issues
Hi Albert,Thanks for your reply.I should start the AIF2 at the accurate LTE timing and set a DL offset, so the tx will be ahead of the real LTE timing to compensate the fiber delay, is this right?And...
View ArticleForum Post: RE: Unabled to connect to board
Hi, Frederick, Im facing to the same problem with you, and I really dont konw how to deal with it. Im a newer and just unbox the EVMK2H. After reading the post, I just wondering if loading a linux...
View ArticleForum Post: RE: I2C cannot work
Renjith,Now I can run the i2c1_mapper in ccs, the problem is that I did not choose the i2cclkenable on scripts.But now I meet a new problem, I can run the demo in ccs by choose i2cclkenable, if not in...
View ArticleForum Post: RE: UART with auto flow for omapl138evm
Hi,[quote]Can you please refer to me serial driver of omal138 in Linux.Actually I was not able to find that...? So that I have a quick look of that...
View ArticleForum Post: RE: K2H EVM: Confirm H264 encode/decode performance
Hi Paula,I had mistakes for my understanding in my previous post.Would you please explain about "420p_8bit.yuv, YUV420, CABAC, VBR, IBBP @ 8Mbps @ 30 frames per second" in "Test Description" at Table 2...
View Article