Forum Post: C6657 SRIOSGMIICLK
I am planning on using the Serial RapidIO (SRIO) Peripheral of the C6657 (http://www.ti.com/product/tms320c6657). It is my understanding that its clock is set from the the SGMII PLL which is sourced by...
View ArticleForum Post: Developing with CCS v5.5 for either C6713 or C6701
I am doing some test dev on the DSK6713 board from spectrum digital. I have developed working code using CCS v3.1 and v3.3 in the past but am trying v5.5 now after a number of years of working on other...
View ArticleForum Post: RE: USB: usb_rx_ch_teardown 1057: teardown Desc not found
Ravi,thanks for sending this out! Is there a reason why this patch was not in the PSP kernel and was not known last year in December, the timestamp seems to indicate that we had this patch already....
View ArticleForum Post: RE: the i/o standard question of connecting fpga and TMS320C6678
Thank you very much ,Bill Taboada . I am thinking about you advices.Now what i am concerning about is that if i choose a bidirectional voltage level translator,dose it influence the datatransmissionspeed.
View ArticleForum Post: RE: XX.out Does not match the target type, not loaded.
"hello world"project is OK.I have already tried,but for mcbsp example,the error is still there.
View ArticleForum Post: RE: 8168 total performance
but i didn't see any decode errors,so i don't know where the frames lost.whether my display configure error cause the display fuzzy?so you said to debug the app ,you can tell me how to debug?make the...
View ArticleForum Post: After loopback run, can I get data in DSP?
Hi I had get raw data by run "./video_loopback_copy_omapl138.x470MV -r720x576".In same time, can I get raw data in DSP? or how can I share it to DSP? Thanks.
View ArticleForum Post: C6678 PCIe drive
Hello!We use PCIe to boot the board. After we connect the board with host computer, the "Properties" in the Device Manager shows that "The device can't get enough available ressources...".What might be...
View ArticleForum Post: RE: question about the SR3_FRAME_BUFFER_EXTRA
Hi, BadriThanks for your reply, I will check the exception trace.What's the means of CPU access the SR3 frame buffer?As I mentioned when I allocated 46 buffers, there is one SR3 frame buffer would be...
View ArticleForum Post: RE: Capture_get will call some DSP function or not?
Hi Titusrathinaraj: I get data success by run "video_loopback_copy_omapl138.x470MV". But I have some question about raw stream. After "video_loopback_copy_omapl138.x470MV" run, can I get...
View ArticleForum Post: FIR filter implementation in C55xx processor
Hi All,I am Application engg and i promoted TMS320C5535 DSP to customer for digital stethoscope application, they want four channel ADC input and wants to implement FIR filter that must support upto...
View ArticleForum Post: NOP instruction,taking 6cycles
Greetings,i am working on c674x dsp of omapl138 processor.i am using NOP instruction, in between of convolution.asm function.while debugging,i saw that NOP is taking 6cycles,which seriously...
View ArticleForum Post: Cache enabled, DSP-RESET / L2-memory corrupt
Greetings,Recently i am facing problem of DSP-RESET when cache is enabled,and i am using cachable ddr2 memory section(using #pragma data_section to place buffer there.)when cache is disabled my code is...
View ArticleClik here to view.
Forum Post: ti816x use THS8200 output VGA have biright line on display right!
Hello: I use dvrdk350,when I use ths8200 to output VGA,when set resolution as 1080P60 or 720P60,there a line on the display left,some time is blue,some time is green.but HDMI display is OK(use...
View ArticleForum Post: using tvp5158 and dm6437 clock problem
I just want there is only one clock source(27Mhz cystal), and I don't need audio input , just need 4-ch half D1 vedio input from tvp5158 using line-interleveaed mode to DM6437, Is that possible?I want...
View ArticleForum Post: ressource distribution for device c6678 by Host PC
Hello!When the board insert the PCIe slot, how does the Host PC distribute ressource to c6678(2.0)?When this process happens, is it related to IBL?Thanks!
View ArticleForum Post: RE: Run dvr_rdk_demo_mcfw_api.out "VDEC + VDIS - SD/HD Decode...
I know the problem, thanks for your help.
View ArticleForum Post: RE: how to get video data after swms and before display
You can use ipcFramesOutVPSS -> ipcFramesInHost to get the frames on A8
View ArticleForum Post: RE: how to boot c6657 in nand
hI Rajasekaran, The nand flash we use is the same with evm board,that means it is ONFI,isn't it? If the answer is yes, so do you mean that we just need to generate the boottable,and then...
View ArticleForum Post: RE: xds510 finds multiple devices in jtag scan chain while only...
The Board connected via XDS 560 successfully but is not connecting via XDS 510 USB.Anybody??
View Article