Forum Post: Boot question 8148
Hi, If I load the u-boot.min through JTAG into nand. How can I tell if it's running without the serial port. Also I only have the XDV100V2 JTAG...ThanksDave
View ArticleForum Post: Insert Audio Algorithm here! 5535 eZdsp and Connected Audio...
Hello,I am having a hard time trying to find out how to modify, or insert code in the example project included in the Connected Audio Framework. In the app_audio_alg.c file it says clearly where to /*...
View ArticleForum Post: RE: C6657 PCIe and Windows.
Dear Eric,Thanks!I found the file. And I check the contents.I was able to get compiler C6000_7.2.0.But, I failed to network install of MinGW by network security.I think method of installing...
View ArticleForum Post: RE: Can I get C55x 4day Workshop Materials?
Interesting. I would have been the person to develop that workshop and, I didn't. ;-) Chapters 8 and 9 of the IW55 workshop I sent you have chapters on optimization regarding the C compiler - how to...
View ArticleForum Post: RE: encode fps
The time interval may be not 10 second.(Please visit the site to view this file)Thanks very much.
View ArticleForum Post: RE: boa get the data post from the web,sometimes it get the wrong...
Thankswe use the DM8127 RDK3.5.0i read the boa code ,all i know is the original http request is the get method,and also there is a cgi(it is post),but when i read the defines.h file i find this:#define...
View ArticleForum Post: RE: rare case: "Overflow detected on VIP0"
Dear Brijesh,Does TI provide some tools to monitor DDR bandwidth momentarily?or What command can I use to check this issue on DM8148/Linux?Thx ~HB
View ArticleForum Post: exections of core M3VPSS, core M3VIDEO and core DSP are all...
Hi, all!We are using DVRRDK_04.00.00.03 and TI8168, and we are encountering an issue.The issue doesn't always occur.When the issue occurs, DVRRDK will stop at the line below in load.sh: ./wait_cmd.sh s...
View ArticleForum Post: RE: Can't get the YUV frames from buffer when use the DEC and...
Hi Badri, I have modified the souce code,and I have go through the "fileRead->decode->fileWrite" .but I can't not get any frame infomation via the function...
View ArticleForum Post: RE: c6670 SPI NOR boot
Hi Rahul,Sorry for interrupting you.I have a question about SPI_Bootloader.zip which you attached to this post.There nysh.spi.map inside this zip file.My question is about the nysh.spi.map.In...
View ArticleForum Post: RE: C6678 SRIO SHADOW REGISTER BEHAVIOUR
Hi Gabriele,Yes, your understanding is correct.The total shadow registers that can be assigned to each LSU is configurable, for a total of 32 sets of registers of the total of 32 shadow register, 16 of...
View ArticleForum Post: RE: Booting from NAND flash memory
Oh, allow me to conclude everything, so that people like me would not face the same issue in the future.Steps to boot from NAND:Prepare a Linux host. (Ubuntu 10.04 LTS in this case) or virtual machine...
View ArticleForum Post: RE: 6678 SRIO low-level test program
Hi Jeff,Thanks for your reply. If you have any issue on DSP side means continue this thread, otherwise please close this thread.Thanks,
View ArticleForum Post: RE: DM8168 proto bring up
Hello Lakshmi, with SD boot mode, not able to see any messages on UART0. But as i told you with 00001 Boot Pin Settings, able to see continuously printing 'o' character. Regards,Pragnesh Virani
View ArticleForum Post: RE: memory alloc fail when "./video_loopback_copy_omapl138.x470MV...
Hi,From the error looks like there isn't suffice memory for the application. This isn't coming from cmem config as from the logs it depicts the buffers are being allocated by the driver, I am sure this...
View ArticleForum Post: RE: Boot Sequence stuck on Waiting for SFT on AM1808
Are you testing this board for a first time?It is the similar board with the DDR2 Replaced by a new one, So yes i am testing this board for the 1st time.Have you initialized the DDR using gel script?I...
View ArticleForum Post: RE: help with OMAPL138 SYS/BIOS and starterware USB
Hi,It is bit difficult to find out the problem,Better to integrating the small starterware code like UART instead taking bigger starterware code such as USB to test the PSC module control function.It...
View Article