Clik here to view.
Forum Post: 8107 DVR RDK Live View Video Quality
Hi, We have a custom board running DVR RDK framework (GA3.0). Its been observed that video is not that sharp as compared with other commercial DVR's. Far objects are not easily distinguishable...
View ArticleForum Post: RE: DM8168, norflash-writer.
Hello again,The first problem is solved with padding pull-down on address pins.The second question is not solved.Thank you.
View ArticleForum Post: RE: DM816x data handling data from VIP1 to VPSS
Hi Lo, This mux settings is also correct, there is no module enabled in the path, mux is configured to accept YUV422 data from VIP1_A and store it as YUV422 data.Now i can think of only one thing, can...
View ArticleForum Post: RE: DM8127 ISS Resizer Two Streams
Hi Terry, Yes, resizer on DM8127 supports two independent outputs from resizer and this has been tested in IPNC-RDK. Could you check if your configuration is correct? it should not give purple output...
View ArticleForum Post: DM385 video freezed after removing the UART cable
Hi,1. Boot the system with video capture and display(HDMI) mode2. remove the UART debug cable3. remove the HDMI cable at TV side4. insert the HDMI cable at TV side5. Noticed the video got freezed.With...
View ArticleForum Post: RE: TMS320VC5509A fail to disable the internal oscillator
Steve, Yes, the emulator is certainly disconnected. The board is on its free run. The CPU is booted from the SPI flash. Unfortunately, we have no any C5509A DSK and it seems are unable to buy, since...
View ArticleForum Post: RE: M3 Hanging with encoder fault
I see, the Encoder LINK should be created for the maximum input resolution, that is, if the potential input resolution includes 720P60 and 1080P30, it should be created for 1080P30.But the initial...
View ArticleForum Post: RE: Not able to boot SD card on hyperterminal OMAPL138LCDK
i have executed the script that u have provided on Ubuntu it executed successfully and after connecting the switch to sd/mmc mode and connected the kit with hyperterminal it gives errorNAND: 512...
View ArticleForum Post: RE: Help with ECU (VoLIB 2.1.0.1). 64ms filter not working properly
Hi Garret, sorry for the late response.I believe I found the problem.Using the 64ms echo tail filter, the manual states that the Buffer's #15 (Search Scratch Buffer) size is 256 bytes. Using the...
View ArticleForum Post: RE: Setting accumulator buffer sizes
Them what is the role of the number of host descriptors in relation to the other 2?
View ArticleForum Post: RE: TFTP MCSDK video in big Endean mode
Hi Vinit,Can you please provide all the files you have modified from MCSDK Video in order to use big endian?Thanks,Hongmei
View ArticleForum Post: RE: C6678 VLAN Aware
If you disabled ALE bypass, you will not be able to receive any unicast packets. You need to either: send out a unicast packet first, so this can be added to ALE automatically and you can receive...
View ArticleForum Post: RE: DM8168 power-up instability
We are stuck at the exactly same place. The trace vector is also 0x06, and the boot rom is stuck at the same place. Some of our boards work, and some don't. If any of you have solved the problem,...
View ArticleForum Post: RE: C6678 Local reset problem
We have "hello world" in ti\mcsdk_2_01_02_06\tools\boot_loader\examples\pcie, it boots multiple cores. The code is in DDR3 (not MSMC). First core 0 is boot up, then it sent IPCGR to other cores to boot...
View ArticleForum Post: RE: UART1 configuration issue on MityDSP-L138
Oleh,I wanted to point you to a Wiki page on the Critical Link support website that previously covered how to get the UART echo StarterWare demo working for the MityDSP-L138 family of...
View ArticleForum Post: RE: Monitoring value of Accumulator A?
Hi Michael,Please see the C55x v3.x CPU Reference Guide: http://www.ti.com/lit/ug/swpu073e/swpu073e.pdfThe accumulators are memory mapped. Pages 2-5 and 2-6 have the locations of the four accumulators...
View ArticleForum Post: RE: CVDD(0.9 to 1.1)current for TMS320C6678:
Hi Srinivasarao, Using the UCD9222 and the UCD7242 as you've described is an approved method of generating the smart reflex power supply needed for the C6678. You may also want to look at the UCD74120...
View ArticleForum Post: RE: UART0 configuration issue - TMS320C6748 DSP
Hi Sivaraj,Thank you for the reply.I have coded based on "biospsp_03_00_01_00\drivers\examples\evm6748\uart\src\uartSample_main.c"According to the example, I have mapped the ECM.eventGroupHwiNum[] to...
View ArticleForum Post: RE: insufficient data error with JPEG encoder
Hi Wenxiang, please see attached lib with fix. JPEG_E.02.02.03.00 would be published at http://software-dl.ti.com/dsps/dsps_public_sw/codecs/C6678/index.html starting next week thank you,Paula(Please...
View ArticleForum Post: RE: Combining NDK with OpenMP
Hi Pubesh,I am combining the image processing OpenMP demo with the UDP echo server example. The problem is not with the udpHello.c file, but with the helloworld file. I haven't been able to initialise...
View Article