Forum Post: RE: Need to know what Tools are available for the TMS320VC5502 &...
Hi Skip,1. When you purchase the C5502 eZdsp, you can use CCS for free, unlimited, as long as it is used with the eZdsp.2. DSP/BIOS is free and comes with some fairly basic...
View ArticleForum Post: 6482 CSL support
Hi I want to use C6482 Chip Support Library, but in the below website it does not contain 6482. So can anyone tell me how to find a CSL support 6482?Thank YouXIning...
View ArticleForum Post: RE: MPM related queries for 6636k2h12
Hi, Vishal,the dspmem currently specifies load address of 0xa0000000, and mpm_config.json file has the corresponding ddr memory address. Both need to be modified for the change.The DSP log messages can...
View ArticleForum Post: RE: What are MPU models exist for KeyStone 2 SoC
The announced Keystone devices supporting ARM are:66AK2H0666AK2H1266AK2H1466AK2E0566AK2E02Regards,Travis
View ArticleForum Post: RE: C6678 SRIO PLL Configuration
[quote user="Alpaslan Lorasda����"]Q1. Form the value of configPLL, the MPY value =00110010. But this value is seemed to be inaccurate according to SRIO UG table.3.7. [/quote]C6670 and C6678 Serdes...
View ArticleForum Post: C6748 : Type conversion question
Hi everybody, Today, while I was programming my C6748 DSP, I encountered a situation that I do not understand. Maybe you will be able to explain me what happened !So, the problem is a conversion from...
View ArticleForum Post: RE: Issue of increasing HDVICP2 heap memory (DM8168)
Hi All, I also trying to increase the amount of memory for openMax (IPC_SR_FRAME_BUFFERS) my application consumes more than 188MB so the default memory map doesn't work for us and the share region...
View ArticleForum Post: RE: About srio line loopback
We have not tested this capability at TI. I would imagine that the 80ps phase offset is fine, as long as the two sources are synchronized in frequency/drift, but I am not certain.I don't believe...
View ArticleForum Post: RE: Twin die DDR3 supported in C6678?
Hi Tom,Thank you for the reply.Actually this question was from my customer.They are considering a device right now, so that it's not in design stage yet.I saw the following post which you...
View ArticleForum Post: RE: "No ETH PHY detected" error in Leopard DM368
Dear TitusThanks for your help. You may find the board-dm368-leopard.c file in the following lines. It is the file that I modified based on your comments (I have specified my comments within the...
View ArticleForum Post: RE: DM648 VPORT FVID_create() failure
I see that mdCreateChan() is never getting called. Actually GIO_create() [FVID_create() is just a wrapper around this] from BIOS lib call this function. Am I missing anything in the tcf file?
View ArticleForum Post: RE: Change NAND size from 256MB to 512MB
hellowhat should I change on the uboot and Linux kernel?> please also remember to check followinga. addressing cycle table b. command table before the above, the following should be check first ~a....
View ArticleForum Post: RE: New Custom AM1802 Board Boot from SD Card
We are getting off topic. I expect you need to change the build options to include NAND support since nand has been part of u-boot for many years. In terms of this thread, booting from SD card, the key...
View ArticleForum Post: RE: Change NAND size from 256MB to 512MB
Thanks, HappyNewYear, I think the address cycle and command table are the same with the one come with the EVM board, I am already test it on the EVM board, it works good so far, what I concerned is on...
View ArticleForum Post: RE: singlecore bootloader --- multicore bootloader
Simon,You would need to provide more details: what is the byte count for that section? Is this from hex6x? Usually it should be padded so size will be a mutiple of 4 bytes. I think you can trace it...
View ArticleForum Post: VD and HD pins
Having an issue with small percentage of our product that uses the davinci chip, TMS320DM6446AZWT, where the chip stops streaming video. We have a TI decoder chip that encodes analog video into 656...
View ArticleForum Post: OMAP-L138 DDR2 JESD79-2A signal levels
Hi,At the moment we have a design with an OMAP-L138 in combination of a Micron DDR2 device. In this design we use no series termination between the devices.This is our situation:After measurements we...
View ArticleForum Post: How are Raster LCD interrupts triggered ?
Hi,I'm trying to run VPIFLCDLOOPBACK test code on starterware provided for evmomapl138 .Only the VPIF interrupts are getting triggered correctly but not lcd raster interrupts ?
View ArticleForum Post: RE: About the voting window ?
Hi Xi,The voting window is 12 data samples as mentioned in the SerDes Implementation guide. I'll investigate why the SRIO user guide suggests that it's 8 data samples and ensure it is updated to the...
View ArticleForum Post: DSPBIOS vs. RTSC
Hi team, I have a question thats applicable to all multi or single core DSP’s or ARM’s. I am trying to understand the relationship between SYSBIOS and RTSC which I believe is Eclipse related and the...
View Article