Forum Post: DVRRDK4.1 memory error
hi,all.I am working on UDWORK dm8168, with the DVRRDK4.1.I have used eth_offload,Previewed 4-channel storaged 11 (the resolution of channels greater than or equal to 2k).But after half an hour ,System...
View ArticleForum Post: RE: New AM1802 Custom Board Bring-up
Something that isn't right is that I don't see RESETOUT (pin T17) go low when RESET (pin K14) is pulled low. RESETOUT is pulled high to 3.3V through a 10k resistor.
View ArticleForum Post: RE: XIP_MUX0 boot problem
hello, Pavel according to DM814x datasheet 4.2 Boot Modes, GPMC_A[1:12] pulling state is IPD. Do I need to use external pulling resistors to pulling them down? BR,qiuxicj
View ArticleForum Post: RE: What can cause the "Port unrecoverable error": bit 2 in...
Hi Travis,Thank you for the reply.I uderstood.best regards,g.f.
View ArticleForum Post: RE: AIF2 in C6670 , RX loss symbols sometime
Hi Albert, thanks for your reply.In my program I used exactly 140 QMSS descriptors for the AIF2 rx FDQ,so I assume the 140 symbols(0..139) received will always corresponding to a certain descriptor,...
View ArticleForum Post: RE: Speed up fprintf or fwrite
Thanks!It should be CCS limitation. CCS fetch memory value from EVM can't be speed up......
View ArticleForum Post: RE: Question about C6670 SRIO Error register
Hi Travis,Sorry, let me check about RIO_SP(n)_ACKID_STAT register.I read SRIO User Guide(sprugw1b) for Keystone.In page.214 "3.14.23 SPn_ACKID_STAT", Outbound_ackID is Read/Write bit field.But it seem...
View ArticleForum Post: RE: dsp clkout have no signal
Dear RandyP:Thank you very much for your help, and you are very right. :) Now I am very sure that my problem is resulted from the reset of DSP IC.My DSP IC is TMS320C6713BZDP-225. Its top mask is the...
View ArticleForum Post: RE: C6678 SRIO endianess
Hi Travis Thank you for answering.Since B0 - B15 is the data in lanes, I am puzzled by such questions: 1. Does bit map in VBUS map to the memory address? In other words, does VBUS 7:0...
View ArticleForum Post: RE: Audio In of Beagleboard xM Rev.C is not working
Sorry, I have no board now, I have not done it for a long time.
View ArticleForum Post: Unique identifier for DM3730
CONTROL_DIE_ID value is not guaranteed unique by TI.http://e2e.ti.com/support/arm/sitara_arm/f/791/t/170736.aspxDoes the DM3730 have a identifier that is guaranteed unique for every chip by TI? Can the...
View ArticleForum Post: RE: Disable output m3vpss messages at console UD DVR Linux
Kill the remote_debug_client process to stop m3 debug msgs.You can also modify the run_gui.sh script to not run the remote_debug_client in the first place
View ArticleForum Post: RE: D1 have noise but CIF ok
As I mentioned disable scd in dspAlg link and then confirm you dont see any corruption.The debug can then focus on the changes you have done that is corrupting decoder reference buffers.
View ArticleForum Post: RE: New AM1802 Custom Board Bring-up
I made a little progress by double clicking on the ccxml file and that showed me the page with the Advanced settings.I don't think ICEPICK is supposed to be there is it?
View ArticleForum Post: RE: network speed
hello Yogesh, by checking, I got below for eth0 (without offload)# ./ethtool -k eth0Offload parameters for eth0:rx-checksumming: offtx-checksumming: offscatter-gather: offtcp-segmentation-offload:...
View ArticleForum Post: RE: JTAG daisy chain connection among C6654, AM3354 and altera...
I got you. Thanks, Bill.
View ArticleForum Post: RE: Can I connect C6654 to AM3354 using mcBsp and mcAsp?
Thanks, Steven.I decided to connect them to CPLD to cover the risk.
View ArticleForum Post: RE: Help! Why does it takes so long to execute the painter...
Thanks for your suggestions, Shankari.
View ArticleForum Post: SPRU433J tms320c55x chip support library manual api reference guide
I'd been reading the tms320c55xx chip support library api reference guide the last publication was sept 2004 it mentions the earlier processor like 5502...5510 but I'm using the ezdsp 5535 or...
View ArticleForum Post: RE: C6657 EDMA problem
Hi, Steven Thanks for you reply. I checked this folder before, but there is only sem2 folder in it, no edma_test.c....... Is this because the vision of BIOS_MCSDK I installed is old. Do I need...
View Article