Quantcast
Channel: Processors
Viewing all 124323 articles
Browse latest View live

Forum Post: RE: AM625: Boot Stall and Crashes

$
0
0
Do you have the ability to enable the on die temperature sensor to see what is the corresponding SOC temperature relative to your temperature chamber your older posts had the following Climate Chamber: KWP 120 Start Temperature: -40.3�C End Temperature: -39.8�C Measured Temperature: -40.3�C Shelf Temperature: -39.5�C Shelf Name: Shelf_19 Module Serial Number: 15313474 Module Location: Shelf 1, Carrier Board 5 Test duration: 127.82s Is the issue reproducible with warm reset or do you power cycle the board? we ran another test with about 50 reboots and yet no failure, of course single EVM. Ice formation on the board , so not planning to run long hour test yet.

Forum Post: RE: TMS320DM648: TMS320DM648

$
0
0
Hello Joanne Goh Thank you for the query. I am checking internally with the team how best we could support. I will update you when i hear from the team. Regards, Sreenivasa

Forum Post: RE: AM6442: Can AM6442 support this kind of programming method?

$
0
0
Hi Thank you for the query. I am reviewing the query and will update you at the earliest. Regards, Sreenivasa

Forum Post: RE: AM6442: AM6442: TI DEMO board: TMDS64EVM, schematic diagram: 3.3V in PROC101D, CPU current design is 1A .BUT the 100mA evaluated by TI power evaluation xls tool .It is very different.

$
0
0
Hi, Thank you for the query. I am reviewing your inputs and checking internally. I will update you at the earliest. Regards, Sreenivasa

Forum Post: RE: PROCESSOR-SDK-AM64X: PROCESSOR-SDK-AM64X

$
0
0
[quote userid="602031" url="~/support/processors-group/processors/f/processors-forum/1361536/processor-sdk-am64x-processor-sdk-am64x/5196230#5196230"]A: Yes, It is from mcu_plus_sdk_am64x_08_06_00_48.[/quote] Can you point me to where in the directory the project resides? I can't seem to find it.

Forum Post: CCSTUDIO: CCS Theia Crashing

$
0
0
I am not sure if other people have been having this issue, but CCS Theia (the VSC based IDE) is constantly crashing. When I am editing files the IDE just freezes and then the screen goes blank a minute later. The only way to get it back has been to restart the application. Happens every couple minutes. I have given it a restart as well but no avail. Any advice on how to fix this issue in the short term, and longer-term bug fixes would be greatly appreciated!! Thanks for your help!! Similar issues as CCS Theia Issues - Code Composer Studio forum - Code Composer Studio ︎ - TI E2E support forums Windows 10 Pro CCS Version 1.3.0

Forum Post: RE: AM625: Configure AM62x GPIO as interrupt input pin

$
0
0
Hello Abhishek, Please see this thread: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1359633/am625-configure-gpio-pin-as-a-interupt Best Regards, Anshu

Forum Post: RE: AM623: GPIO interrupt delay tens of milliseconds

$
0
0
As Tony pointed, this is a duplicate and will be closed.

Forum Post: RE: AM69A: Inference with compiled model fails on device, but is succesful on x86.

$
0
0
Here's the output: [C7x_1 ] 606560.277295 s: VX_ZONE_ERROR:[tivxAlgiVisionCreate:335] Calling ialg.algInit failed with status = 1 [C7x_1 ] 606560.283007 s: VX_ZONE_ERROR:[tivxKernelTIDLCreate:910] Network version - 0x00000000, Expected version - 0x20240401 [C7x_1 ] 606560.284490 s: VX_ZONE_ERROR:[tivxKernelTIDLCreate:910] Network version - 0x00000000, Expected version - 0x20240401 [C7x_1 ] 606560.287298 s: VX_ZONE_ERROR:[tivxKernelTIDLCreate:910] Network version - 0x00000000, Expected version - 0x20240401 [C7x_1 ] 606560.288672 s: VX_ZONE_ERROR:[tivxKernelTIDLCreate:910] Network version - 0x00000000, Expected version - 0x20240401 [C7x_1 ] 606560.291381 s: VX_ZONE_ERROR:[tivxKernelTIDLCreate:910] Network version - 0x00000000, Expected version - 0x20240401 [C7x_1 ] 606560.292686 s: VX_ZONE_ERROR:[tivxKernelTIDLCreate:910] Network version - 0x00000000, Expected version - 0x20240401

Forum Post: RE: SK-AM62B-P1: How to bypass the EEPROM checking procedure

$
0
0
[quote userid="600470" url="~/support/processors-group/processors/f/processors-forum/1360917/sk-am62b-p1-how-to-bypass-the-eeprom-checking-procedure/5196535#5196535"][ 5.138709] CPU2: failed to come online [ 5.167810] CPU2: failed in unknown state : 0x0 [ 10.276097] CPU3: failed to come online [ 10.280027] CPU3: failed in unknown state : 0x0[/quote] The above message was due to the AM62x2 SoC on your board which has only dual A53 cores. One option to boot dual A53 cores in Linux: - stop @u-boot prompt - setenv optargs "maxcpus=2" - boot I think the kernel booting issue was triggered by something else. Let's close this e2e, and follow up the kernel booting issue in the following e2e. https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1360910/am625-q1-board-boot-loops-during-kernel-load Best, -Hong

Forum Post: RE: TDA4AP-Q1: Bring up no stable switch on for TPS6594 PMIC possible

$
0
0
Issues resolved with customer via conference call.

Forum Post: RE: PROCESSOR-SDK-AM62X: Is it possible to toggle/change CSI_GPIO1 to active_low after booting on AM62X EVK ?

$
0
0
Hello, Looks like your camera probed according to this thread: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1362717/processor-sdk-am62x-how-to-start-the-ov5647-live-camera-on-ti-apps-launcher . We'll continue the discussion using that thread and close this one. Regards, Jianzhong

Forum Post: RE: PROCESSOR-SDK-AM62X: How to start the OV5647 Live camera on TI Apps Launcher

$
0
0
Hi, The cis-bridge in your media pipe has different format to the sensor. Please configure it to be the same format as the sensor. media-ctl --set-v4l2 '"cdns_csi2rx.30101000.csi-bridge":0 [fmt:SBGGR10_1X10/640x480 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:lim-range]]' Then you can use yavta to capture the images from the sensor, as documented here: https://software-dl.ti.com/processor-sdk-linux/esd/AM62AX/09_02_00/exports/docs/linux/Foundational_Components/Kernel/Kernel_Drivers/Camera/CSI2RX.html#utilities-to-interact-with-the-driver . Regards, Jianzhong

Forum Post: AM5718: [AM57IDK Reference board] Kernel crash after Initializing XFRM netlink socket when docker changes are enabled

$
0
0
Part Number: AM5718 Other Parts Discussed in Thread: DRA722 , TPIC2810 Hello , Greetings!! i want to give the back ground of the work flow: Yocto : dunfell (08.00.00.004) Machine : am57xx-evm Board : AM57IDK kernel : 5.10.41-rt Im currently facing issue after the boot, board enters into kernel OOPs and Panic log " ON in case of Docker configurations enabled." I just picked up the machine file from Yocto dunfell branch and build using bitbake, kernel boot-up is Good and No issues. Issue appears when docker kernel configurations fragments are enabled. Here the crash log: [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.41-rt39-g0701a5b58c (oe-user@oe-host) (arm-poky-linux-gnueabi-gcc (GCC) 9.5.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT_RT Tue Jul 20 18:16:38 UTC 2021 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: TI AM5718 IDK [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x00000000be800000 [ 0.000000] OMAP4: Map 0x00000000afd00000 to (ptrval) for dram barrier [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afcfffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000afd00000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] node 0: [mem 0x00000000a0000000-0x00000000abffffff] [ 0.000000] node 0: [mem 0x00000000ac000000-0x00000000afcfffff] [ 0.000000] node 0: [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] DRA722 ES2.0 [ 0.000000] percpu: Embedded 11 pages/cpu s15776 r8192 d21088 u45056 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 259654 [ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait console=ttyO2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x0000000091800000-0x0000000095800000] (64MB) [ 0.000000] Memory: 570212K/1045504K available (10240K kernel code, 741K rwdata, 3380K rodata, 6144K init, 291K bss, 295068K reserved, 180224K cma-reserved, 237568K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] rcu: RCU_SOFTIRQ processing moved to rcuc kthreads. [ 0.000000] No expedited grace period (rcu_normal_after_boot). [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x350/0x504 with crng_init=0 Starting version 244.5+ [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.001281] TI gptimer clockevent: always-on 32786 Hz at /ocp/interconnect@4ae00000/segment@10000/target-module@8000 [ 0.001831] TI gptimer percpu-dmtimer: 20000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@34000 [ 0.001922] Failed to initialize '/ocp/interconnect@48000000/segment@0/target-module@36000/timer@0': -22 [ 0.003662] Console: colour dummy device 80x30 [ 0.003692] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2' [ 0.003692] This ensures that you still see kernel messages. Please [ 0.003692] update your kernel commandline. [ 0.003723] Calibrating delay loop... 1993.93 BogoMIPS (lpj=9969664) [ 0.061920] pid_max: default: 32768 minimum: 301 [ 0.062011] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.062042] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.062683] CPU: Testing write buffer coherency: ok [ 0.062713] CPU0: Spectre v2: using ICIALLU workaround [ 0.062866] /cpus/cpu@0 missing clock-frequency property [ 0.062896] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.063415] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.063507] rcu: Hierarchical SRCU implementation. [ 0.063812] EFI services will not be available. [ 0.063903] smp: Bringing up secondary CPUs ... [ 0.063903] smp: Brought up 1 node, 1 CPU [ 0.063903] SMP: Total of 1 processors activated (1993.93 BogoMIPS). [ 0.063934] CPU: All CPU(s) started in HYP mode. [ 0.063934] CPU: Virtualization extensions available. [ 0.064239] devtmpfs: initialized [ 0.091369] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.091491] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.091522] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.094665] pinctrl core: initialized pinctrl subsystem [ 0.095184] DMI not present or invalid. [ 0.095458] NET: Registered protocol family 16 [ 0.096710] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.099212] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.116607] thermal_sys: Registered thermal governor 'fair_share' [ 0.116607] thermal_sys: Registered thermal governor 'bang_bang' [ 0.116607] thermal_sys: Registered thermal governor 'step_wise' [ 0.116607] thermal_sys: Registered thermal governor 'user_space' [ 2.942382] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2.942382] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 2.981140] V1_2D: supplied by VMAIN [ 2.982818] iommu: Default domain type: Translated [ 2.986328] SCSI subsystem initialized [ 2.986816] mc: Linux media interface: v0.10 [ 2.986846] videodev: Linux video capture interface: v2.00 [ 2.986907] pps_core: LinuxPPS API ver. 1 registered [ 2.986907] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.986938] PTP clock support registered [ 2.986968] EDAC MC: Ver: 3.0.0 [ 2.988159] Advanced Linux Sound Architecture Driver Initialized. [ 2.989013] clocksource: Switched to clocksource 32k_counter [ 2.995544] NET: Registered protocol family 2 [ 2.995697] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 2.996551] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes, linear) [ 2.996582] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 2.996673] TCP bind hash table entries: 8192 (order: 5, 229376 bytes, linear) [ 2.996856] TCP: Hash tables configured (established 8192 bind 8192) [ 2.996917] UDP hash table entries: 512 (order: 3, 32768 bytes, linear) [ 2.996978] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes, linear) [ 2.997283] NET: Registered protocol family 1 [ 2.997924] RPC: Registered named UNIX socket transport module. [ 2.997924] RPC: Registered udp transport module. [ 2.997924] RPC: Registered tcp transport module. [ 2.997924] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.997924] PCI: CLS 0 bytes, default 64 [ 3.038208] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 3.039031] Initialise system trusted keyrings [ 3.039306] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 3.044311] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.044891] NFS: Registering the id_resolver key type [ 3.044921] Key type id_resolver registered [ 3.044921] Key type id_legacy registered [ 3.044982] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 3.044982] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 3.045013] ntfs: driver 2.1.32 [Flags: R/O]. [ 3.045440] Key type asymmetric registered [ 3.045440] Asymmetric key parser 'x509' registered [ 3.045501] bounce: pool size: 64 pages [ 3.045532] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 3.045532] io scheduler mq-deadline registered [ 3.045562] io scheduler kyber registered [ 3.551086] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 3.857452] OMAP GPIO hardware version 0.1 [ 4.071838] palmas 0-0058: Irq flag is 0x00000004 [ 4.100982] palmas 0-0058: Muxing GPIO 2f, PWM 0, LED 0 [ 4.116241] smps12: supplied by regulator-dummy [ 4.117553] smps3: supplied by VMAIN [ 4.119201] smps45: supplied by regulator-dummy [ 4.120758] smps6: supplied by VMAIN [ 4.122161] smps7: supplied by VMAIN [ 4.123291] smps8: supplied by VMAIN [ 4.124694] smps9: supplied by VMAIN [ 4.126037] ldo1: supplied by VMAIN [ 4.127655] ldo2: supplied by VMAIN [ 4.129272] ldo3: supplied by VMAIN [ 4.130889] ldo4: supplied by VMAIN [ 4.131195] random: fast init done [ 4.131530] LDO5: supplied by regulator-dummy [ 4.131927] LDO6: supplied by regulator-dummy [ 4.132293] LDO7: supplied by regulator-dummy [ 4.132659] LDO8: supplied by regulator-dummy [ 4.134185] ldo9: supplied by VMAIN [ 4.135803] ldoln: supplied by VMAIN [ 4.137390] ldousb: supplied by VMAIN [ 4.152435] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 4.179443] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 4.180694] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 4.186950] edma 43300000.dma: memcpy is disabled [ 4.190216] edma 43300000.dma: TI EDMA DMA engine driver [ 4.206878] pinctrl-single 4a003400.pinmux: 282 pins, size 1128 [ 4.211761] dra7-pcie 51000000.pcie: host bridge /ocp/axi@0/pcie@51000000 ranges: [ 4.211822] dra7-pcie 51000000.pcie: IO 0x0020003000..0x0020012fff -> 0x0000000000 [ 4.211853] dra7-pcie 51000000.pcie: MEM 0x0020013000..0x002fffffff -> 0x0020013000 [ 5.212707] dra7-pcie 51000000.pcie: Phy link never came up [ 5.212860] dra7-pcie 51000000.pcie: PCI host bridge to bus 0000:00 [ 5.212860] pci_bus 0000:00: root bus resource [bus 00-ff] [ 5.212860] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 5.212890] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 5.212921] pci 0000:00:00.0: [104c:8888] type 01 class 0x060400 [ 5.212921] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 5.212951] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 5.213012] pci 0000:00:00.0: supports D1 [ 5.213012] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 5.221038] PCI: bus0: Fast back to back transfers disabled [ 5.228607] PCI: bus1: Fast back to back transfers enabled [ 5.228637] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 5.228637] pci 0000:00:00.0: BAR 1: assigned [mem 0x20020000-0x2002ffff] [ 5.228637] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 5.229156] pcieport 0000:00:00.0: PME: Signaling with IRQ 167 [ 5.236114] V3_3D: supplied by smps9 [ 5.236358] vtt_fixed: supplied by V3_3D [ 5.276367] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 5.280181] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 109, base_baud = 3000000) is a 8250 [ 5.280273] printk: console [ttyS2] enabled [ 5.283172] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 5.284667] DSS: OMAP DSS rev 6.1 [ 5.288452] random: crng init done [ 5.310821] brd: module loaded [ 5.317413] loop: module loaded [ 5.325012] spi-nor spi0.0: s25fl256s1 (32768 Kbytes) [ 5.325073] 7 fixed-partitions partitions found on MTD device spi0.0 [ 5.325073] Creating 7 MTD partitions on "spi0.0": [ 5.325103] 0x000000000000-0x000000040000 : "QSPI.SPL" [ 5.326293] 0x000000040000-0x000000140000 : "QSPI.u-boot" [ 5.329711] 0x000000140000-0x0000001c0000 : "QSPI.u-boot-spl-os" [ 5.330841] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env" [ 5.339752] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1" [ 5.340850] 0x0000001e0000-0x0000009e0000 : "QSPI.kernel" [ 5.341949] 0x0000009e0000-0x000002000000 : "QSPI.file-system" [ 5.344146] libphy: Fixed MDIO Bus: probed [ 5.409088] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 5.409088] libphy: 48485000.mdio: probed [ 5.419952] davinci_mdio 48485000.mdio: phy[0]: device 48485000.mdio:00, driver Micrel KSZ9031 Gigabit PHY [ 5.419952] davinci_mdio 48485000.mdio: phy[1]: device 48485000.mdio:01, driver Micrel KSZ9031 Gigabit PHY [ 5.420593] cpsw-switch 48484000.switch: initialized cpsw ale version 1.4 [ 5.420593] cpsw-switch 48484000.switch: ALE Table size 1024 [ 5.420684] cpsw-switch 48484000.switch: cpts: overflow check period 500 (jiffies) [ 5.420684] cpsw-switch 48484000.switch: CPTS: ref_clk_freq:266000000 calc_mult:4036623398 calc_shift:30 error:-1 nsec/sec [ 5.420715] cpsw-switch 48484000.switch: Detected MACID = 44:ea:d8:17:3a:0a [ 5.420745] cpsw-switch 48484000.switch: Detected MACID = 44:ea:d8:17:3a:0b [ 5.422668] cpsw-switch 48484000.switch: initialized (regs 0x0000000048484000, pool size 256) hw_ver:0019010F 1.15 (0) [ 5.423583] i2c /dev entries driver [ 5.430175] sdhci: Secure Digital Host Controller Interface driver [ 5.430206] sdhci: Copyright(c) Pierre Ossman [ 5.431701] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.433746] omap_gpio 4805d000.gpio: Could not set line 27 debounce to 200000 microseconds (-22) [ 5.433746] sdhci-omap 4809c000.mmc: Got CD GPIO [ 5.435211] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_3_3v mode [ 5.446105] NET: Registered protocol family 10 [ 5.446990] Segment Routing with IPv6 [ 5.447052] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 5.447509] NET: Registered protocol family 17 [ 5.447753] Key type dns_resolver registered [ 5.447814] Registering SWP/SWPB emulation handler [ 5.448303] omap_voltage_late_init: Voltage driver support not added [ 5.448303] Power Management for TI OMAP4+ devices. [ 5.448699] printk: console [ttyS2]: printing thread started [ 5.448730] Loading compiled-in X.509 certificates [ 5.467346] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 5.485260] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 5.533355] dmm 4e000000.dmm: workaround for errata i878 in use [ 5.535339] dmm 4e000000.dmm: initialized all PAT entries [ 5.540863] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 5.543548] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 5.544281] platform 40800000.dsp: Adding to iommu group 0 [ 5.548278] mmc0: new high speed SDHC card at address aaaa [ 5.548858] mmcblk0: mmc0:aaaa SS16G 14.8 GiB [ 5.550079] omap-iommu 58882000.mmu: 58882000.mmu registered [ 5.550567] platform 58820000.ipu: Adding to iommu group 1 [ 5.553161] mmcblk0: p1 p2 p3 p4 [ 5.559539] omap-iommu 55082000.mmu: 55082000.mmu registered [ 5.559967] platform 55020000.ipu: Adding to iommu group 2 [ 5.561614] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 5.561981] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 5.569610] omapdrm omapdrm.0: [drm] Cannot find any crtc or sizes [ 5.570465] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0 [ 5.572448] ALSA device list: [ 5.572448] No soundcards found. [ 5.589141] mmc1: new DDR MMC card at address 0001 [ 5.600006] Freeing unused kernel memory: 6144K [ 5.600402] mmcblk1: mmc1:0001 R1J56L 13.8 GiB [ 5.600616] mmcblk1boot0: mmc1:0001 R1J56L partition 1 4.00 MiB [ 5.600860] mmcblk1boot1: mmc1:0001 R1J56L partition 2 4.00 MiB [ 5.600982] mmcblk1rpmb: mmc1:0001 R1J56L partition 3 128 KiB, chardev (243:0) [ 5.601806] Run /init as init process [ 6.579223] omapdrm omapdrm.0: [drm] Cannot find any crtc or sizes [ 9.886779] EXT4-fs (mmcblk0p5): mounting ext3 file system using the ext4 subsystem [ 9.902374] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) Authenticating root filesystem:...... All OK OK OK ..... [ 44.466522] pps pps0: new PPS source ptp1 [ 44.466705] remoteproc remoteproc3: powering up 4b234000.pru [ 44.485473] remoteproc remoteproc3: Booting fw image ti-pruss/am57xx-pru0-prueth-fw.elf, size 6760 [ 44.485504] remoteproc remoteproc3: unsupported resource 5 [ 44.485595] remoteproc remoteproc3: remote processor 4b234000.pru is now up [ 44.486206] net eth2: started [ 44.580627] remoteproc remoteproc4: powering up 4b238000.pru [ 44.580810] remoteproc remoteproc4: Booting fw image ti-pruss/am57xx-pru1-prueth-fw.elf, size 6792 [ 44.580810] remoteproc remoteproc4: unsupported resource 5 [ 44.580932] remoteproc remoteproc4: remote processor 4b238000.pru is now up [ 44.581542] net eth3: started [ 44.693847] pps pps1: new PPS source ptp2 [ 44.694030] remoteproc remoteproc5: powering up 4b2b4000.pru [ 44.694152] remoteproc remoteproc5: Booting fw image ti-pruss/am57xx-pru0-prueth-fw.elf, size 6760 [ 44.694183] remoteproc remoteproc5: unsupported resource 5 [ 44.694244] remoteproc remoteproc5: remote processor 4b2b4000.pru is now up [ 44.697753] net eth4: started [ 44.804901] remoteproc remoteproc6: powering up 4b2b8000.pru [ 44.804992] remoteproc remoteproc6: Booting fw image ti-pruss/am57xx-pru1-prueth-fw.elf, size 6792 [ 44.805023] remoteproc remoteproc6: unsupported resource 5 [ 44.805114] remoteproc remoteproc6: remote processor 4b2b8000.pru is now up [ 44.805755] net eth5: started [ 54.613433] Initializing XFRM netlink socket [ 60.651580] br0: renamed from ov-001000-ysj3p [ 60.790374] vxlan0: renamed from vx-001000-ysj3p [ 60.829559] br0: port 1(vxlan0) entered blocking state [ 60.829681] br0: port 1(vxlan0) entered disabled state [ 60.829956] device vxlan0 entered promiscuous mode [ 60.830200] 8 ] lr : [ ] psr: 200a0013 [ 61.029052] sp : c1a71e80 ip : c1a71e48 fp : efc34d80 [ 61.034301] r10: 00000100 r9 : fffffffe r8 : c16b74f8 [ 61.039550] r7 : c1a71ea0 r6 : 00000009 r5 : c372f7a0 r4 : 00000001 [ 61.046112] r3 : 00000009 r2 : c1a71ea0 r1 : 00000000 r0 : c9dd0000 [ 61.052673] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 61.059844] Control: 30c5387d Table: 89c038c0 DAC: fffffffd [ 61.065612] Process kworker/0:1 (pid: 18, stack limit = 0x70c8efd8) [ 61.071929] Stack: (0xc1a71e80 to 0xc1a72000) [ 61.076293] 1e80: c9df8400 c1a70000 c9dd0000 c9df8410 c16b74e0 c0af3794 00000100 c0af407c [ 61.084533] 1ea0: c9dd0000 00000000 c9df8410 c1a71ed3 00000000 54a78262 efc32330 c9df8400 [ 61.092742] 1ec0: c1a70000 c0af4118 00000000 00000200 01000001 54a78262 00000200 c9df8400 [ 61.100952] 1ee0: c9df8410 c9dd0000 c0af3808 c0af4224 c9df8400 c16b74c8 c16b74c8 c0af37dc [ 61.109161] 1f00: efc34d80 efc38000 c16b74e8 c1a55200 efc34d80 efc38000 00000000 00000000 [ 61.117401] 1f20: 00000000 c0af38a4 c16b74e8 c0241aa0 efc34d98 c1605100 c1a55200 efc34d80 [ 61.125610] 1f40: c1a55214 efc34d98 c1605100 00000008 c1a70000 c0241d48 c1a55200 c16b91a7 [ 61.133819] 1f60: c1a71f74 c1a51dc0 c1a70000 c1a51d80 c1a58800 c0241cfc c1a55200 c1897eac [ 61.142028] 1f80: c1a51de4 c0248474 c1a58800 c1a51d80 c02482e8 00000000 00000000 00000000 [ 61.150268] 1fa0: 00000000 00000000 00000000 c0200140 00000000 00000000 00000000 00000000 [ 61.158477] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 61.166687] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 61.174926] [ ] (prueth_sw_switchdev_blocking_event [prueth]) from [ ] (0xc1a70000) [ 61.184204] Code: e8bd87f0 e5920000 e1a03001 e5901600 (e591116c) [ 61.513092] ---[ end trace 0000000000000002 ]--- It is only after the Initializing XFRM netlink socket, it enters into OOPs. I have picked up docker cfg from https://git.ti.com/cgit/processor-sdk/meta-processor-sdk/tree/recipes-kernel/linux/files/docker.cfg?h=dunfell_8_2 Can community please suggest how to fix and where im going wrong what is missing ? Regards, Raju

Forum Post: RE: AM625SIP: When will AM625SIP be in mass production?

$
0
0
Hi Hochun, Hope you are doing well! The MP will be at the end of this month. Best, Mahir Kaheri

Forum Post: RE: SK-TDA4VM: How do use tiovxmux with v4l2h264enc

$
0
0
Hi Vivek, Which SDK version are you using? What camera sensor are you using and what is your output format? I am going to try this out on my end, but in the meantime, have you tried tiovxdlcolorconvert? Thank you, Fabiana

Forum Post: RE: TDA4VM: TDA4VM C660 opcode exception with SDK7.3 and ROV context error

$
0
0
Hi, TI Experts, TDA4VM aboted again, show as follows: 1. Checked with CCS, found that C661 has crashed, with the crash caused by an Opcode Exception (IERR=0x8,NRP=0xB2E401C0). 2. When check the debice, the CCS connection is loose. Attempts to reconnect to C660 and C661 were unsuccessful, but connections to R5F2, C7, and other cores are success. 3. At this time, through R5F2_0, the memory of C661 was saved. 4. After the device was restarted and operating normally, multiple attempts to connect to C661 with CCS failed, and other cores could connect normally. 5. Under the condition of multiple device restarts and occasional connections to C661, but C660 not, the memory of C661 was loaded. 6. When comparing the memory before and after, discovered two code location are modified. However, they were found to be unrelated to the NRP( NRP= 0xB2E401C0 ). A. address: 0 x B 2F0A6F8, 0xA1EF0c6E-> 0xA1EF3 C6F B. address : 0x B2F0DBA0,0x00000000-> 0x 1001E000 7. Upon retesting, when the normal device memory was modified to the above error value through CCS, the device run ok continuly. 8. When the device's debug board was swapped, found that CCS connections to other boards were normal, but the abnormal device, could not connect to C660 and C661, while other cores normal connectivity.

Forum Post: RE: PROCESSOR-SDK-AM62X: v4l2-ctl setting not available on SDK v9.2 with MIPI camera

$
0
0
Hi Nakanishi-san, Apologies for the delay in responding. OV5640 is default set as 30fps for VGA in the driver, so you can't achieve 60fps framerate. https://github.com/torvalds/linux/blob/master/drivers/media/i2c/ov5640.c#L3866 Please modify the driver to set to 60fps and give it a try and see if it helps. Best Regards, Suren

Forum Post: AM62A7: EdgeAI Modelmaker: r9.1 VerifyOutputSizes error

$
0
0
Part Number: AM62A7 Hello, I'm bringing up a custom board, and was working in SDK 9.0 with the EdgeAI Modelmaker repo r9.0 to prototype object detection models. I was able to train each of the YOLO models and deploy without issue. To resolve some unrelated driver issues, I had to upgrade to SDK version 9.1.7 a few weeks ago. I just switched to the correct branch (r9.1) of EdgeAI Modelmaker , and now get this issue when running inference: 2022-04-30 19:59:53.738820485 [W:onnxruntime:, execution_frame.cc:835 VerifyOutputSizes] Expected shape from model of {-1} does not match actual shape of {1,1,1,1,1,200} for output labels 2022-04-30 19:59:53.739074035 [W:onnxruntime:, execution_frame.cc:835 VerifyOutputSizes] Expected shape from model of {-1,5} does not match actual shape of {1,1,1,1,200,5} for output dets If I disable TIDL execution, the model runs slowly, without error, on the CPU. Which seems to point to compilation/artifacts as the issue. If I remove the output node from allowedNode.txt (283, I believe), it also runs without issue - just too slow for my requirement. The output shape prints as: NodeArg(name='dets', type='tensor(float)', shape=['Concat1482_dim_0', 5]). It seems the dimension of the referenced layer is not populating correctly. I attached the tarball as output by the modelmaker. If you have any idea what is going on, I would appreciate the help. Thank you e2e.ti.com/.../od_2D00_8270.tar.gz

Forum Post: RE: SK-AM62B-P1: I have encountered a boot issue and would appreciate your assistance in resolving it.

$
0
0
The e2e looks like the same issue reported in this e2e https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1360910/am625-q1-board-boot-loops-during-kernel-load Let's not do duplicate posting... Best, -Hong
Viewing all 124323 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>