Forum Post: AM3352: DM Timer
Part Number: AM3352 Tool/software: Hi Support Team, I have been asked about the DMTimer 1ms by a customer who uses the AM3352. We are currently developing a model that uses this timer and interrupts...
View ArticleForum Post: RE: AM3359: In AM3359 after RAMFS only 1 Ethernet Port is working
Hi Schuyler, DTS file as below /* * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/ * * This program is free software; you can redistribute it and/or modify * it under the terms...
View ArticleForum Post: RE: TDA4VM: std::priority_queue performs differently in release...
Hi, which core this problem is observed in. [quote userid="611930"...
View ArticleForum Post: RE: CCSTUDIO: How to set "--printf_support=minimal"? (Using...
The tiarmclang compiler does not support the option --printf_support . Instead, it automatically chooses the smallest variant of the printf routines that can support the format specifiers ( %s , %d ,...
View ArticleForum Post: RE: TDA4VH-Q1: Calibration ONNX QDQ Prequantized Model
Hi Halil, Sorry for the late response on this. Your compilation settings look fine to me. I would like to investigate this on my side further. I will be reaching out to your FAE via regarding getting...
View ArticleForum Post: RE: AM3352: NAND Boot issue
It is good to know booting u-boot from NAND works on your board now. How did you flash kernel/rootfs to NAND? Best, -Hong
View ArticleForum Post: RE: AM3352: data abort during kernel load
There's tons of changes from u-boot 2014 to u-boot 2022, for example, DT are incrementally added. Have you adapted your SW for u-boot 2022? Best, -Hong
View ArticleForum Post: RE: AM623: Read Extended OTP from linux application
K3conf is developed for calling TISCI APIs (clock etc...) from "non-secure host". It might require more code changes in K3conf to enable calling TISCI APIs from "secure host". Is SoC_UID applicable...
View ArticleForum Post: RE: AM623: uSD Card Detection Without Card Detect
Refer to "broken-cd" property in MMC node as noted in the referenced e2e in my last reply....
View ArticleForum Post: RE: AM6412: USB hangs after repeated cable insertion and removal
Hi Tashiro-san, [quote userid="97804" url="~/support/processors-group/processors/f/processors-forum/1298733/am6412-usb-hangs-after-repeated-cable-insertion-and-removal/4991274#4991274"]They put 4.7uF...
View ArticleForum Post: RE: AM623: eMMC rpmb read error
Hi， Has there been a response to this question？ Regards, Li
View ArticleForum Post: RE: SK-AM68: SD card creation error
Thank you for your comment. I am using Ubuntu 22.04 and Balena Etcher 1.19.17. I have used this combination for several months to make SD cards for the boot of the other edge devices. Also, I tried...
View ArticleForum Post: RE: AM3352: DM Timer
Hello Kanae, How are you programming the DM Timer? e.g., are you using a driver from a particular operating system? I am sending your thread to a member of our hardware team for now - I'm the Linux...
View ArticleForum Post: RE: AM69: Suggestion for a processor part having 4 or more ADC cores
Hi Please share your comments
View ArticleForum Post: RE: AM3352: UART baud rate and timer3 period change during --25C...
Hello Tony, Checking if customer made any PLL changes. Can you please request the customer to dump the PLL configuration registers Regards, Sreenivasa
View ArticleForum Post: RE: AM3354: How to calculate the temperature of SOC with...
Hello Zekun, Thank you for the query. Please check if the below FAQ helps...
View ArticleForum Post: RE: AM625: difference of IBIS model each version
Hello GR, Please refer below inputs. It is in the “File Rev” section of the model file. D version has the additional comment below: - Removed unsupported models for LVDS, IIC and eMMC IO buffers The...
View ArticleForum Post: RE: AM3352: Control Status register' s value
Hello Kanae, Thank you. BOOT_SEL understanding is correct. Could you please request customer to capture for a longer time (ms) I am checking with the team internally. Regards, Sreenivasa
View ArticleForum Post: RE: AM5728: Quesstion about AM5728 EMAC RX_START_OF_FRAME_OVERRUNS
Hello, experts: Sorry，I don‘t understand,What is Start of Frame,And We use the RGMII interface and the 100M mode of KSZ9131 is used instead of the 1000M mode. Is it because the sending interval of...
View ArticleForum Post: RE: TMS320C6713B: I have built a project for C6713, after doing...
I think the program is not saved in flash, the program is lost after power reset
View Article