Forum Post: RE: Connection Error while erasing NAND using Serial Boot
The settings exactly matches the OMAP L138 board, since we have following the OMAPL138 board architecture. RAM, NAND, Ethernet are attached on the same address
View ArticleForum Post: RE: Got screen messed up while using DEI link for scaling
Hi ! Badri !I wonder what would happen if I use DEI link with input resolution is greater than 1920x1080, would it will make screen mess up?Thanks!
View ArticleForum Post: RE: DM3725 Video Encoding issue
More information:1) use "malloc()" instead of "Memory_alloc()", this time (memcpy) could be reduced to 3.x ms, but the video encoding doesn't work;2) enable cache, this time can be reduce to ~30ms, but...
View ArticleClik here to view.
Forum Post: RE: DEI LINK affects video quality?
Badri, thank you for your answer.I have modified the code(as you suggest).Effect is much better, but did not reach the effect of the original(links:vcap_vdis)vcap-vdis: vcap-dei-vdis: It is easy...
View ArticleForum Post: RE: How to modify External Memory timing setup for DDR2 at 240MHz
Hi,Refer the below location in serial flash utility source code.OMAPL138/Common/include/device.hextern __FAR__ Uint32 DEVICE_ExternalMemInit(Uint32 ddrphycr, Uint32 sdcr, Uint32 sdtimr, Uint32...
View ArticleForum Post: UART in IBL for 6678 to make IBL similar to u-boot
HiAny one tried of bringing the UART prompt in IBL itself before booting application ( from nor/nand)Idea is to make IBL similar to U-boot by bringing the prompt to the user before booting and user can...
View ArticleClik here to view.
Forum Post: RE: dm816x Can not reshuffle graphic(0~2) layer.
hi Ralph.Thank you for your reply.I hope that it works as shown in the figure below.use sysfs : #echo 1,0/2/1/3 > /sys/devices/platform/vpss/display0/orderHowever, it is performed as shown...
View ArticleForum Post: RE: Connection Error while erasing NAND using Serial Boot
############################################################## Common build definitions for Makefile use...
View ArticleForum Post: RE: why can't execute encode and decode module simultaneously in...
HI,Ramprasad , thank you for your reply very much!Maybe you misunderstand my issue.My omx program is omx progam with a single process. All capture，dei, encode, decode and display components are builded...
View ArticleForum Post: RE: AM1808 silicon version 2.1 boot from SD card
Hi Mr.Titu I tried the to options UART boot and NAND boot. 1.UART boot built the u-boot with some modification in UART clock sampling and signed the u-boot by AISGen tool then tried to boot from...
View ArticleForum Post: RE: how to pass paramter from DSP to ARM?
If you want to pass large sized data than using ipcBitsOutLink ->ipcBitsInLink is the right method. You can send any data using ipcBitsOutLink->ipcBitsInLink. There is no restriction that it is...
View ArticleForum Post: RE: [Capture] Cannot capture video immediately once I run the...
Under what condition does your application send LinkControl cmd CAPTURE_LINK_CMD_SET_RESOLUTION. Sending that cmd will result in print "CAPTURE: Dynamic resolution change: width: 1920, height: 1080"It...
View ArticleForum Post: RE: C6678 SRIO Enumeration
HiKnow its a old postbut as years passed by curious to know whether currently SRIO Enumeration is possible in 6678 or not?Planning to design a board with multiple 6678 chips along with a SRIO...
View ArticleForum Post: RE: SRIO Help for Beginners (C6678 and SRIO switch)
Hi BrandyJDid u ever tried SRIO Enumeration in 6678...Planning to design a board with multiple 6678 chips along with a SRIO switchHow to do SRIO enumeration in this case ?
View ArticleForum Post: RE: DM8148 gamma correction
Hi Brijesh,Previously, you mentioned "The gamma correction is supported only on HDMI VENC, which also can output digital signals on Vout1, so you will need to connect your lcd to vout1".Please help to...
View ArticleForum Post: RE: Ethernet Interface and IEEE1588, 802.3 AVB
Don,[quote user="Don Lydon"]Do I need to use a specific Ethernet Interface (RGMII, G/MII, RMII) on the AM3874 to support IEEE1588, 802.3?[/quote]This is the feedback from our AVB expert:Our MAC ports...
View ArticleForum Post: Rebuilding the Flash and Boot Utils package for a particular...
Can someone explain me the steps to Rebuild SFH tool on WindowsI have installedCCS4Cygwin Setuparm-2011.03-41-arm-none-linux-gnueabi.exe(Sourcery G++ Lite 2011.03-41)C6000 Code Generation Tools...
View ArticleClik here to view.
Forum Post: RE: TMS320C6670 - OMP Example Project
Hi Ganapathi, Yes, I followed "BIOS MCSDK 2.0 Getting Started Guide" for CCS and MCSDK installation.I have removed "C:\ti\omp_1_01_03_02\packages" from include path and...
View ArticleForum Post: RE: [AM1808] UART boot code generated by AISgen has incorrect...
Yes, the kernel source need to fix also, as:Under driver/serial/serial_core.cunsigned intuart_get_divisor(struct uart_port *port, unsigned int baud){ unsigned int quot; /* * Old custom speed...
View Article