Forum Post: RE: keystone SRIO physical loopback connection evm6678L
You can not simply solder wires to the AMC connector edge and expect these Gb/s links to function. This is not supported since signal integrity with match impedance differential pairs is needed. Any...
View ArticleForum Post: RE: C6657 DDR3 DQ vs DQS timing
James,I was forwarded additional information on the issue that you have been reporting. We need to review and get back to you. The sample point is ideally set to the most robust sampling point while...
View ArticleForum Post: RE: optimizing EDMA PCIe transfers for read/write and multiple cores
Jeff,Are you using CPU to do the verification and enabling the cache? If so, I am wondering if any cache coherence operation or disabling the cache could help.If you disabled the L1/L2 cache already,...
View ArticleForum Post: RE: C6678 PG1.0 vs PG2.0 Boot ROM functionality
Sorry for my delayed response. I have contacted some colleagues on my team for their feedback on this issue. My current understanding is the same as one and zero's response above. You should only need...
View ArticleForum Post: RE: DDR3 Controller Config via GEL File
Tom-A quick question -- I could not find the answer on other threads -- is there some way that current revision 6678 EVM mem can be increased to 2 GByte ?Thanks.-JeffSignalogic
View ArticleForum Post: RE: assembly branch to C function link error
Hi Randy,Sorry, it takes a long time for me to reply this thread. Here's my final code for the interrupt vector table:.ref _c_int00 .ref _dsp_interrupt_defaultIsr .ref _gpTimer5_isr_dsp .ref...
View ArticleForum Post: RE: How to run dvrrdk3.0 on 8168EVM with IO card
I found different topics on this , however, there are different sayings, I am not sure which is correct.
View ArticleForum Post: ECG processing using OMAP-L138
Hi good evening,I am trying to process some biomedical signals (mostly 3-lead ECG signals) throught my OMAP L-138 board, but I am having a hard time with the setup and data acquisition.Can someone...
View ArticleForum Post: Can I connect C6654 to AM3354 using mcBsp and mcAsp?
Dear TI.We need to transfer some data between C6654 and AM3354 using mcBsp. But I found that AM3354 only had mcAsp port.Can I connect them using C6654's mcBsp and AM3354's mcAsp? Do they have master...
View ArticleForum Post: I have a problem while creating a multi-core deployment...
HI!I have a problem while creating a multi-core deployment configuration file.The source file is programmed along MCSDK user's guide.This source has a simple function flashing LED on the EVM6678 and...
View ArticleForum Post: JTAG daisy chain connection among C6654, AM3354 and altera max2...
Dear TI.My board have C6654, AM3354 and Altera max2 CPLD devices. I need to debug them using the JTAG port, But I don't want to add 3 JTAG ports on in design. Could I connect them to one JTAG port...
View ArticleForum Post: RE: How to run dvrrdk3.0 on 8168EVM with IO card
DVRRDK doesn't support EVM+XIO daughter card so there is some porting effort.First migrate to DVRRDK 4.1 and then refer this most where EVM+XIO daughter card is used to capture 720P using...
View ArticleForum Post: RE: How to integrate Codec Engine for DM8148 RDK
Integration is not impossible but is quite complex and since we have not tried it we don't know what issues you will face when you try integration.There is no difference in terms of functionality...
View ArticleForum Post: RE: Queary Regarding keystone 2 Netcp
Thanks Bill for providing the right understanding.Also,Internal IP == NetCP ,right?
View ArticleForum Post: RE: Capture Issue: "Overflow detected on VIP0"
Your capture link configuration is correct ( SYSTEM_CAPT_VIDEO_IF_MODE_16BIT/SYSTEM_CAPT_VIDEO_CAPTURE_MODE_SINGLE_CH_NON_MUX_EMBEDDED_SYNC). Continuous VIP overflow indicates bad input signal.CHeck...
View ArticleForum Post: RE: DM8127IPNC: problem running ipnc_rdk_mcfw.out stand alone
Can you tell me ,how did you solved this problem, when I execute this cmd ,I only get :root@dm814x-evm:/opt/ipnc# ./ipnc_rdk_mcfw.out TRISTREAM APPRO2A AEWB [c6xdsp ] Remote Debug Shared Memory @...
View ArticleForum Post: dm8127 RDK 3.5 ipnc_rdk_mcfw.out problem
In the RDK,I want to execute ipnc_rdk_mcfw.out after init.sh，I can,t see anything at hdmi out; root@dm814x-evm:/opt/ipnc# ./ipnc_rdk_mcfw.out TRISTREAM APPRO2A AEWBAPPRO2A AEWB [c6xdsp ] Remote Debug...
View ArticleForum Post: PCB layout query using TI DSP TMS320C6746
I have few quarries related to PCB layout using TI DSP TMS320C6746 and are mentioned below :We are using three interfaces i.e HPI, Memory and MCBSP from DSP6746, and an external High speed Asynchronous...
View ArticleForum Post: RE: ti-sdk-beagleboard-06.00.00 OTG Issue
Hi Shulev ,I found a similar issue reported for am35xx and for older kernel.http://e2e.ti.com/support/arm/sitara_arm/f/791/t/189348.aspxBin Liu has posted a patch for this issue , Which is no longer...
View ArticleForum Post: RE: nvr gui
thanks for your answerno i can not .i have a question,in the NVR GUI demo,the default url is: define NETWORK_URL_DEFAULT...
View Article